Table of Contents
How do you clean linear rails?
Apply a small amount of 99% isopropyl alcohol to a lint-free paper towel. Wipe down the length of the rail with the paper towel, ensuring that you grip the sides of the rail tightly. This will allow the paper towel to clean the groove down the side of the rail, as well as the other surfaces.
What do you use to clean a 3D printer?
Using a filament cleaner removes all types of dirt (lint, dust or other dirt) before the filament enters the extruder, increasing the duration of the same and the nozzle of the 3D printer, as well as avoiding jams caused by accumulation of dirt.
How do you lubricate hiwin rails?
HIWIN linear guideways can be lubricated with grease, low-viscosity grease or oil, depending on the specific application. The required lubricating pressure depends on the size, the lubricant, the length of the feed line and the type of lubrication connection used.
How do you clean a clogged 3D printer?
First, clean the nozzle using a damp cloth or an alcohol wipe while the nozzle is hot. This may cause some steam but will indeed remove any material clinging to the nozzle. If this doesn’t work, you can also use a wire brush, small blade, or needle to remove any remaining debris from the nozzle.
What can dissolve PLA?
What solvent will dissolve PLA filament? Ethyl acetate, methylene chloride, propylene carbonate, acetone, and pyridine are the commonly used PLA solvents. The first three can be used to dissolve PLA supports or clean your printer, while the rest are mainly used to smooth or glue printed parts.
How do I unclog my Hotend?
Cool down your extruder to room temperature to solidify the filament in the nozzle. Set the hotend to 115°C. At 90°C, pull on the filament until it yanks out of the nozzle. This should leave the shape of the inside of your nozzle on the end of the filament.
How often should you clean your 3D printer?
How Often Should I Clean My 3D Printer Nozzle? You should clean your nozzle as and when it gets fairly dirty or at least every 3 months for regular maintenance. If you don’t clean your nozzle too often, it’s not the end of the world, but it does help to give your nozzle more life and durability.
How often should you clean 3D printer nozzle?
Poor quality or cooked/burned filament can leave residue in your nozzle. Even PLA can solidify in the nozzle over time, so we advise flushing it through at least every 200 – 400 printing hours.
What is white lithium grease spray used for?
White lithium grease is used to keep components moving smoothly, free of friction and seizing. You can also apply it preventatively to protect against rust and corrosion. White lithium grease can be used to: Lubricate car door hinges.
What is EP2 grease?
Print. Tweet. Valvoline Lithium EP2 Grease is a premium quality lithium soap grease containing extreme pressure additives, formulated to provide outstanding mechanical stability & EP characteristics under severe operating conditions.
What oil is used for linear rail?
Linear systems typically use lithium-based greases, with no solid additives such as MoS2 (molybdenum disulfide) or PTFE (Teflon), in consistency class between 0 and 3. These greases perform well in high-load applications and have good stability against oxidation.
What is the best grease for linear bearings?
Thomson offers LinearLube® grease which is suitable for most industrial applications. DO NOT use any type of dry lubricant (PTFE powder, graphite powder, etc.) with any recirculating ball or roller type of bearing. While these lubricants are good for sliding motion, they do very little to aid rolling friction.
Do you need to grease linear bearings?
You may be accustomed to greasing your linear bearings, but that’s not necessary anymore. igus® linear bearings are designed with wear-resistant plastic liners that are embedded with solid, dry lubricants, such as PTFE and silicone.
What is NLGI grease?
A grease with an NLGI grade of 1 has a consistency like tomato paste, where a grease with an NLGI grade of 3 has a consistency more like butter. The most commonly used greases, such as those used in automotive bearings, would use a lubricant that is NLGI grade 2, which has the stiffness of peanut butter.
How often grease linear bearings?
We recommend lubrication every three months even if the lube is still clean and present. If you have a low cycle application, you way want to start with a lubrication period of 1 week, then two weeks and so on.
What is NLGI #2 grease?
NLGI 2 grade grease has a consistency similar to peanut butter. Grease consistency is a major contributor (in combination with additive technology, base fluids, and types of thickeners) to the performance of a grease and how well it will execute lubrication tasks in specific applications.
How do I know if my printer nozzle is clogged?
Manually push the material out of the nozzle, once it has fully heated up. The material should slowly protrude out of the nozzle. If it doesn’t, this means your nozzle is clogged.
What is nozzle cleaning?
The nozzle is the component used to direct a flow of material throughout the entire printing process, allowing the printer to form the desired shape of a model. Cleaning the nozzle in acetone is a way to keep it in good condition and extend its life span.
How do I clean printer heads?
Make sure that the printer is turned on and the ink out light is off. Access the Print or Page Setup dialog box and click the Utility icon button, then click the Head Cleaning button. Follow the on-screen instructions. The power light and the ink lights flash while the printer performs the cleaning cycle.
Why does my 3D printer nozzle keep clogging?
If the temperature of your hot end is too low, your print material will not melt correctly. This can cause the material to begin to adhere to the inside surface of the nozzle. Eventually, the extrusion motor can’t feed the filament into the head and before you know it your 3D printer nozzle is clogged.
Does acetone melt PLA?
Yes, acetone can dissolve PLA but only under certain conditions. You might get better results with other solvents, but there isn’t one that reliably works for all types of PLA filament. PLA is an excellent 3D printing material, but it does not offer a lot of post-processing options.
