Table of Contents
How to Clean the Thermocouple in a Gas Fireplace Turn off the fireplace gas valve and remove the front panel from the fireplace. Find the thermocouple, which is located next to the pilot light and looks like a small straight pipe. Use a can of compressed air to gently blow away any dust and dirt from the thermocouple.
How do I know if my thermocouple is bad on my gas fireplace?
The Fix: Pilot Light to Gas Fireplace Won’t Stay Lit So you’ve checked your pilot light and even reset it, but still, it wont stay lit. This can be an indication that your fireplace thermocouple is either bad or worn out.
How do you clean a thermocouple?
The best way to clean your thermocouple is to use either a piece of steel wool or the coarse side of a sponge to gently clean off any soot or other remnants. You can use a pencil eraser to clean between the threads of the screw that connects the thermocouple to the control valve of your system.
What does a bad thermocouple look like?
Before jumping to the conclusion that the thermocouple is at fault, look at the pilot flame. If it appears small and has an orange-yellow tinge, it may be too weak to heat the thermocouple. The likely problem, again, is an obstruction in the pilot tube.
How long does a thermocouple last on a gas fireplace?
How to Tell if You Have a Bad Thermocouple? Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
Can you clean a fireplace thermocouple?
A dirty thermocouple may affect the ability of the gas fireplace to ignite. Cleaning the thermocouple is a pretty simple process but should only be done when the fireplace is turned off and is completely cool. Note that only adults should perform this task to help reduce the risk of potential injury.
Why is my thermocouple not working?
If the appliance has a thermocouple, the problem may be a faulty thermocouple. The thermocouple, which operates as a safety device, turns the gas supply off when the pilot light goes out. When a thermocouple fails, the pilot light won’t stay lighted. A burned out or broken thermocouple should be replaced.
Why won’t my pilot light stay lit in my gas fireplace?
If the pilot light on your gas fireplace won’t stay lit, a very likely culprit is a component called a thermocouple. A thermocouple is a safety device and is a component of the ignition system. Its purpose is to not allow the gas valve to open if the pilot light isn’t lit.
Do thermocouples go bad?
Like the other component parts in your furnace, the thermocouple can wear down over time, producing lower voltage than it should when heated. And the worst part is that you can have a bad thermocouple without even knowing. Therefore, inspecting and testing your thermocouple should be part of your furnace maintenance.
Can you bypass thermocouple?
Realistically, you have just disabled the thermocouple, but you can also reach in and unclip it from its holding bracket where it meets the pilot light. In most cases it will be held on with a gravity clip, but some are held on with a screw that must be removed with a small screwdriver.
How much does it cost to replace a thermocouple in a gas fireplace?
When replacing a thermocouple or thermopile with the help of a professional, you can expect to pay between $150 and $250.
Why does my gas fireplace go out after a few minutes?
If you get dust in the pilot assembly and the pilot needs to be cleaned out, it produces a “lazy” flame, which will be disturbed by the draught of the main burners. The flame lifts away from the thermocouple and causes the temperature on the tip of the thermocouple to drop. This, in turn, makes the gas valve shut off.
How do you troubleshoot a thermocouple?
Importantly, always make sure the tip of the thermocouple is directly in the pilot flame. If the tip is in the flame, you have held the nob on the gas valve down for longer than a minute, the pilot flame is strong and steady, and the pilot still does not stay lit, then you likely have a problem with the gas valve.
What causes a thermocouple to fail?
METAL FATIGUE Like everything, thermocouples can’t stay new forever. Changes in temperature can cause regular expansion and contraction in metal, which will cause thermocouples to weaken over time. After enough time, metal fatigue can cause a thermocouple to break.
Can a thermocouple be bad if the pilot stays lit?
The function of a thermocouple in a gas valve is to assure that an active pilot light is functioning properly to ignite any supply gas. If the thermocouple fails, for any reason, the gas flow must be shut down even if the pilot is properly lit. The function is termed a “Fail Safe” mode.
Will cleaning thermocouple help?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
How much does it cost to have a thermocouple replaced?
It costs $150 to $250 to replace a thermocouple. It checks to make sure the pilot light is on. It will shut the gas off if it’s not.
Can you overheat a thermocouple?
A: Thermocouples are designed to be low maintenance items. If the back end of your thermocouple bulb gets constantly overheated, it will fail. With excessive back pressure coming from the burner ports, thermocouples can get burned up quickly.
