Table of Contents
The first step is to read the check engine light code provided by the car’s computer system. This is the information that’s been logged by the sensors in your engine. It can be read with OBD II scanners or readers through a connection (OBD port) usually located under the steering column.
Can I check my own check engine light?
Can I Check My Own Light? You can. All that you need to check your own light is an OBD-II reader, which can pull codes that help you find out what’s wrong with your car.
How can I check my check engine light without a scanner?
Flip your car’s ignition on and off a couple of times without cranking the engine and finish with the key in the on position. Your car will then check for any saved trouble codes. All the lights on the dash should light up until one remains on—usually the “service engine” light.
Does AutoZone check your check engine light for free?
Many drivers don’t realize that AutoZone, the nation’s largest auto parts chain, will do the following services free of charge: Read the codes on your check engine light. Test your battery’s voltage. Check your alternator and starter.
How do you read a check engine light code?
How to read OBD codes: Preparation. Step 1: Plug the OBD scanner into the OBD port. Step 2: Turn on the ignition. Step 3: Enter the Vehicle Identification Number. Step 4: Find OBD codes in the menu. Step 5: Interpret the first character of the OBD code. Step 6: Interpret the second character of the OBD code.
What is the most common reason for check engine light?
Replacing a faulty oxygen sensor — a sensor used to optimize a vehicle’s fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.
How much does it cost to check engine light?
On average, the fee to have an auto mechanic diagnose a check engine light is $100.
Can you reset check engine light without disconnecting battery?
Turning the Ignition On and Off Switching the ignition on and off is also one method of hard reset without disconnecting batteries. Put the keys in your ignition and turn your ignition on and off consecutively after a second in each step. Once it is done, see if the engine check light is still coming on or not.
What does a solid check engine light mean?
A solid Check Engine Light can mean something like a loose gas cap, or it can indicate a more in-depth problem like a fuel, timing, or transmission issue. Get your car diagnosed, although the urgency isn’t the same as if the light was flashing at you.
How long does it take to diagnose a check engine light?
A standard diagnostic test can take about an hour to an hour and a half. Of course, more complicated issues that require further diagnosis and where components must be removed for access or testing can take 2-3 hours; depending on the severity of the issue or multiple underlying issues.
Is check engine light serious?
When your car’s check engine light illuminates on your dashboard, it’s usually accompanied by a sinking feeling in the pit of your stomach. The light could be a minor issue, such as a faulty gas cap, or it could mean something more serious, such as a misfiring engine.
Why is my engine light on but nothing seems wrong?
Normally, the appearance of a check engine light indicates a problem somewhere in your vehicle, but nothing seems amiss. The problem can even be as simple as forgetting to tighten your gas cap – in fact, this is the most common reason why check engine lights appear in the first place.
Why does my car say gas cap loose?
Simply put, if your fuel cap light is on, it means that the computer has detected a leak in the system, typically from a loose gas cap. If this light comes on while driving, pull over in a safe spot and re-secure the cap. If the light doesn’t turn off, inspect the gas cap for any damage and replace it if necessary.
How long do you have to drive to reset engine light?
To make sure the check engine light does not reappear, it’s recommended that you drive your car 30 to 100 miles. This enables the vehicle’s “Drive Cycle” to reset, as the various sensors need time to recalibrate.
Why is my engine light on and car jerking?
Blocked Fuel or Air Intakes Inside of your engine air mixes with fuel and is lit by the spark plugs to create an explosion that moves the pistons inside. If there is a block in the lines that allow fuel or air into your engine, then this cycle is interrupted and can cause your car to jerk as you try to accelerate.
What happens when you clear check engine light?
When you clear codes, you also clear diagnostic data When the check engine light comes on, a trouble code is stored and freeze frame data is stored. A trouble code lets us know which computer test failed. The freeze frame data shows us the data the computer saw at the time of the fault.
Can I reset check engine light myself?
Turning the Ignition On and Off The on-off method is the equivalent fix for a vehicle’s check engine light. It forces the computer to refresh its saved state through a reboot. Simply place your key into the ignition and turn it on for 1-2 seconds, then turn it off for 1-2 seconds. Repeat this step three or four times.
