Table of Contents
Open the spigot and drain a little water to relieve some pressure and heat inside the tank before opening the top for the anode rod. Next, go to the top of your water heater and look for a hex head bolt. If you don’t see the hex head, it’s likely built into your water heater system.
How do you know if you have a bad anode rod?
A bad anode rod can cause discolored water, a rotten egg smell, air in the lines and intermittent hot water. The anode rod protects the tank of electric water heaters & signs it should be replaced are a rotten egg smell, no heat & strange sounds.
How do you check a water heater anode?
Turn Off Water and Fuel Supply (Gas or Electric) Locate the gas line near the bottom of your water heater. Drain Some Water. Locate Anode Rod. Loosen the Hex Head and Remove the Anode Rod. Install New Sacrificial Anode Rod. Turn Off Water and Fuel Supply (Gas or Electric) Drain Some Water. Locate Anode Rod.
When should anode rod be replaced in water heater?
By replacing your anode rod every 3-5 years, your water heater can last well over 20 years without any risk of leaks and resulting water damage. Unfortunately, if you ignore this important water heater maintenance task, you may need to replace the entire water heater after only 10 years of use.
Can an anode rod be cleaned and reused?
You cannot clean your anode rod in your water heater . However, it is important to inspect the sacrificial anode rod every 1 to 3 years and replace it after more than 50% of its wear and tear to avoid corrosion of your tank.
How do you know if anode rod is magnesium or aluminum?
A magnesium rod will generally last less than an aluminum rod. One issue with aluminium rods is that the corrosive material that is formed on the anode tends to harden and sink to the bottom of the water tank.
What happens if you don’t change your anode rod?
When the rod itself becomes so corroded that it can no longer do its job, the tank soon rusts out, leaks and needs replacement. However, if you replace your water heater anode rod before it fails, about every five years, you can double the life of your water heater.
Are anode rods universal?
In most cases, water heater anode rods are universal. The only exceptions are : Buderus : They use another type of threading to install the magnesium anode. All other water heater brands use a regular magnesium anode with 3/4 ” NPT threads.
How long will a water heater last without an anode?
Diminished Water Heater Lifespan: Without a sacrificial anode rod replacement, the average tank water heater will last a maximum of 8-12 years. However, your water heater may start failing as early as 5 years old without this essential care.
Can anode rod causing rotten egg smell?
The most common cause of smelly water is anaerobic bacteria that exist in some water and react with the magnesium and aluminum sacrificial anodes that come with most water heaters to produce hydrogen sulfide gas, making the classic rotten egg odor.
How much does it cost to replace an anode rod?
An anode rod costs about $50. Some homeowners may feel comfortable replacing it themselves. If not, call a professional plumber, who can assist. The cost of having it replaced professionally may be around $250 or $300.
How do I know what size anode rod to buy?
As a rule you want the anode to be “tip to toe” running the full height or length of the tank. If you cant see your brand on the chart then just measure the length of the tank and pick the closest length of anode. If the anode is too long they can be simply cut to length with a hack saw.
How often should you flush a water heater?
Tip: To maintain the upkeep of your water heater, flush your water heater every six months or so. If you have harder water, or water that contains more minerals, you may want to flush it more often.
Are aluminum zinc anode rods safe?
Aluminum is well-tolerated by plants and animals, and exhibit low toxicity. resort, as emergency preparedness experts advise, you don’t want the bottom of water heater to be full of aluminum compounds. They’re hard on your stomach and intestines, and can cause arthritis-like symptoms in joints.” End quote. anode rod.
Are magnesium anodes toxic?
Magnesium anodes are also non-toxic, and have an extremely active electro-chemical voltage range that makes them even more effective than aluminum.
Can you cut down an anode rod?
Yes, you can cut your sacrificial anode rod, whether it is magnesium or aluminum, to replace it. To do this, use a pair of gloves and a saw and cut as you remove the old anode. In confined spaces, cutting the anode rod technique is often used.
Does a gas hot water heater have an anode rod?
Inside the Tank In glass-lined tanks, there will be a metal rod in the tank, usually magnesium or aluminum, called a sacrificial anode. The anode rod is bolted and fastened to the top of the tank and extends deep into the tank.
How do you flush a hot water tank?
How to Flush Your Hot Water Heater Turn the Knob on Your Hot Water Heater’s Thermostat to “Off” Turn Off Gas to Hot Water Heater. Turn Off the Cold Water Supply to Hot Water Heater. Turn on the Hot Water in a Sink or Tub. Connect Garden Hose to Drainage Spigot. Turn on Spigot and Drain. Flush.
What size socket do you need to remove an anode rod?
4 Use a ratchet wrench and 1 1/16-inch deep socket to unscrew the anode rod from the heater.
Are anode rods standard size?
The diameter of residential water heater anode rods is universal at 3/4 inches. However, the length and type of the anode rod may not be the same. Also, some anode rods are attached to the top of the water heater, while others are connected to the hot water outlet.
Do you need an anode rod if you have a water softener?
If you have a water softener system, you should have the anode rod of your water heater inspected and replaced more frequently. This is a fairly simple process – and certainly much cheaper than replacing the entire water heater unit.
