Table of Contents
How do you remove the light cover on a ceiling fan?
Most oyster glass covers of modern fans are removed by turning the glass gently anti-clockwise. If the glass does not move, tapping the glass with a tool containing a soft edge such as a rubber casing around the handle in an anti-clockwise direction can help to loosen it.
How do you remove fluorescent light covers without clips?
Wrap your fingers under the edge of the light cover if there are no clips or tabs. Pull outward and down. A lip on the inside of the cover may hold it in place. Set the cover gently on the ground or a work table so that it does not get scratched.
How do you remove a canopy trim ring on a Hunter ceiling fan?
To remove the canopy trim ring, press firmly on opposite sides of the ring towards the canopy as shown in Figure 21. The tabs will flex out releasing the trim ring from the canopy. Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan).
How do you remove an overhead light cover?
Firmly, but Gently, Pull the Glass Out Then, once you’ve found it, use those hand-muscles and pull the clip firmly (but still gently) away from the glass cover. When you get the clip moved far enough, you should be able to pull the glass cover out from under the clip, freeing it from the ceiling mount.
How do you remove a plastic dome light cover?
Access the plastic ceiling light, using a stepladder. Remove the plastic light shade by twisting it counterclockwise. Alternatively, loosen the fitter screws around the light base to remove the shade.
How do I remove a ballast cover?
Remove the Cover Plate Locate the wiring cover plate, usually in the center of the fixture. On either side of the cover, there will be tabs that catch in slots in the fixture. Squeeze the sides of the cover inward to slip the tabs out of the slots, and pull the cover down. This will expose the ballast and its wiring.
How do you open a fluorescent light bulb cover?
To remove an acrylic cover from a fluorescent light fixture, push up on one of the short ends of the cover while supporting the other short end with your other hand. As you push up on one short end, angle that end of the cover up into the light fixture a little bit.
How do you remove a circular fluorescent cover?
Remove the light fixture’s cover to expose the bulb. Unscrew the decorative knob at the center of the cover. Twist the entire cover counterclockwise. Loosen several small screws located along the perimeter of the cover. Lift open several clips found along the perimeter of the fixture where it meets the ceiling.
How do you remove ceiling rosettes?
Pull down gently on the putty knife handle, prying loose one small portion of the rosette or plaster. Adjust the blade left or right, then pry again. Repeat around the rosette until it is loose enough to pull off.
How do I remove a Hunter ceiling fan cover?
Remove the canopy trim ring that covers the top part of the canopy on the Hunter ceiling fan by squeezing the ring with two fingers and firmly pulling downward along various points until the ring pops off. Many models use two canopy trim rings; both may be removed this way.
How do you remove a square flush mount ceiling light cover?
How To Remove Square Light Fixture Cover (Easy Steps) Turn Off The Lights. The first thing you need to do is turn off the lights. Climb The Ladder And Put On Your Goggles. Take Out The Square Glass Fixture. Take Out The Bulb. Screw Back The Fixture. Clean The Glass.
How do you remove recessed lights from housing clips?
Inside the recessed light are four black clips that hold the fixture into the ceiling, and each clip has a small slot. Insert a flathead screwdriver into the slot and push up toward the ceiling; this will release the clip and allow the recessed light fixture to be removed from the ceiling.
How do you remove a glass shade from a pendant light?
1. Hold onto the glass, carefully reach inside your pendant from below and unscrew the lightbulb from the threaded socket. Next, unscrew the shade ring to fully release the glass from the socket and cord. See the parts of your pendant light here.
How do I remove a lampshade?
If your lampshade is lightbulb-accessible, follow these steps: Unscrew the lightbulb. Locate the mounting screws. Loosen the mounting screws with your screwdriver until the lampshade comes free. Carefully place the old lampshade down nearby and take your new lampshade up the stepladder.
How do you remove a ballast?
How to Bypass A Ballast Step 1: Disconnect All Power So There is No Electrical Current. Step 2: Find the Ballast. Step 3: Locate and Cut Only the Hot and Neutral Wires. Step 4: Cut the Socket Lead Wires. Step 5: Remove the Ballast (if you wish) Step 6: Connect the Wires. Step 7: Reattach Any Coverings and Turn On.
How do you remove a ballast from a fluorescent light?
According to EPA Toxic Substances Control Act (TSCA) regulations, the material must be incinerated. The entire lighting fixture does not need special handling and disposal as long as the ballast (electrical box) is not leaking. The non-leaking ballasts can be removed and recycled or disposed of properly.
How do you remove a light ballast?
How to Bypass a Ballast Turn off the power. Flipping the light switch to the “off” position does not necessarily end the flow of electricity. Locate your ballast. Cut the hot and neutral wires. Cut the socket lead wires. Remove the ballast. Connect the input wires to the output wires.
Can you remove a ceiling medallion?
To remove a medallion, climb a ladder with a sharp utility knife or razor blade mounted in a scraper-style holder, a wide putty knife or taping knife, and a smaller putty knife or, even better, a small pry bar with a thin blade, such as a Sharkgrip pry bar (www.sharkcorp.com).
How do you remove decorative plaster molding?
Plaster-based products can be soften using a steam wallpaper stripper and stripped off using a decorators scraper. The thickened emulsion paint type can be stripped using a textured paint remover, a special type of paint stripper designed for the job.
