Table of Contents
How to Change Filament Select Filament > Unload Filament. The Smart Extruder+/Smart Extruder will start to heat up. Open the filament drawer and remove the old spool. Select Filament > Load Filament. Wait for the Smart Extruder+/Smart Extruder to heat. Cut the end of your new filament to create a clean edge.
How do you change filaments in Ender 3?
Scroll to Control Settings > Temperature > Nozzle. Use the LCD knob to dial the temperature up. Wait for the hot end to reach the desired temperature. Squeeze the extruder lever to release the grip on the filament, withdraw the filament, and remove the spool.
How do you unload the filament in Ender 5?
Press and hold the extruder lever then insert 1.75mm filament through the small hole of the extruder. Continue feeding until you see filament come out the nozzle.
How do you change a filament?
Removal of current filament Step 1: Preheat your hot end based on the temperature guidelines of your current filament. Step 2: Wait until the hot end heats up to the required temperature. Step 3: Manually extrude a small portion of the filament. Step 4: Push down the coupling to release the filament from the hot end.
Do I remove filament after printing?
Do You Have to Remove Filament After Printing? Most people experience no serious problems after leaving the filament in the extruder. However, there can be a few exceptions too. Whether to remove filament immediately or let it stay overnight, basically depends on the filament type.
How do you fix filament jam?
Try and keep the filament as straight as possible. Natural or clear coloured filament works best so you can see the residue when you pull it out. If your hot end is too clogged to get anything out of the hot end, take a thin wire and a pair of plyers and stick it into the tip of the nozzle to clear the blockage.
How do you keep filaments from tangling?
Prevention. The most important thing is to always hold the end of the filament under tension until it is either in your 3D printer’s feeder or attached to the side of the spool. The latter is accomplished by pulling the end through a hole in the spool or fastening it with tape or a filament clip.
Why is filament stuck?
Filament jams happen when the extruder can’t push filament through the hot end. The extruder either grinds the filament until it’s so thin that the gear that advances the filament is no longer in contact with it, or the motor that drives the extruder stalls because it’s overloaded.
How do you remove PLA from extruder?
Heat the nozzle to the lower end of your ABS filament temperature and push or extrude until you get the ABS color. Allow the hot end to cool to the low end of PLA temperatures and reverse the extruder/pull out the filament.
How do you remove a stuck filament in Ender 3?
If the filament is broken at the spot where the filament cannot be removed using wire then you should: Heat up the nozzle up to 200°C. Handle the filament using tweezers or pliers. Pull out the filament slowly out of the extruder. Keep on pulling it until it is completely removed from the PTFE tube.
What temperature does PETG print at?
PETG has a moderate printing temperature, typically printing between 230°C – 250°C.
What temp should pla be printed at?
What temperature to print PLA? In general, PLA filament settings have an optimal printing PLA temperature range from about 185C to about 205C. If you’re using 1.75mm as opposed to thicker 2.85mm (or 3.00mm) your optimal print will be closer to the lower end of this PLA filament temperature range.
Do you need to keep filament dry?
If you’re using PLA filament, silica gel packs must become your best friend. Simply place the gel packs into sealable Ziploc bags, Tupperware, or anything else that won’t let air get inside. In the end, though, keeping your filament dry using silica gel is a neat and easy method for keeping your filament dry.
Does filament go bad?
Unlike food which has a specific expiration date, filament does not have a specific expiration date. However, filament can go bad based on storage conditions. The worse the conditions the quicker the material will go bad. If you notice the print quality suffering, the first thing to check is your filament.
How long does it take for PLA to go bad?
While in an adverse environment, PLA is said to last between a few months to two years. While PLA is not water-soluble, it has a fairly high rate of water absorbency, or in technical terms, is hygroscopic. Exposure to moisture will lead to poor results when put into your 3D printer with the high-temp nozzle.
Are all PLA filaments the same?
It is mostly the same, with a few slight differences: better surface quality, color, and mechanical properties. Most PLA+ filaments are advertised as being stronger, less brittle, more durable, and better for layer adhesion. Tough PLA is another term used by some manufacturers.
How do you remove a tube filament?
Stick something long and thin down the tube and push the broken filament out. An easy way to do this is by using a piece of fresh (non-brittle) filament. Alternatively, you can use a long metal rod like a thin welding rod, or my favorite, a guitar string.
How do I unclog my Hotend?
Cool down your extruder to room temperature to solidify the filament in the nozzle. Set the hotend to 115°C. At 90°C, pull on the filament until it yanks out of the nozzle. This should leave the shape of the inside of your nozzle on the end of the filament.
How do I stop my 3D printer from jamming?
Make sure that your 3D filament is loading into the printer properly, with minimal tension outside of the extruder. Be sure that the spool of filament is mounted and is able to spin freely – often tension from the filament leading to the extruder can cause a printer to stop extruding.
Why is my Ender 3 not extruding?
The main reason was as @0scar suggested – the nozzle was too close to the build plate preventing the filament from exiting – and the back-pressure was causing the filament to jump back, giving the extruder a “shudder” as it slips on the filament.
Does Ender 3 V2 have filament Sensor?
The Ender 3, Pro, and V2 are all pretty similar, with the exception of the Ender 3 V2’s upgraded (V4. 2.2 or V4. 2.7) 32-bit mainboard. The new mainboard has additional ports for a BLTouch and a filament runout sensor, as well as a pre-installed bootloader for flashing new firmware through the microSD card slot.
