Table of Contents
How do you replace fascia board yourself?
How To Replace Roof Fascia Board Step One: Inspect the Existing Fascia. Step Two: Remove Gutters and Drip Edge. Step Three: Remove Existing Fascia Board. Step Four: Measure and Cut. Step Five: Cover the Seams. Step Six: Seal the Wood. Step Seven: Install Drip Edges and Gutters.
Can I replace fascia myself?
Luckily, replacing a fascia board is as easy as taking out the old board and fitting a new one in its place. Once you’ve installed a new board, all you need to do is seal the seams and paint it to match your home. With a short afternoon renovation, you can have new fascia boards that will last for years!.
How much would it cost to replace fascia boards?
1. Average Cost to Replace Fascia and Soffit Cost Per Linear Foot Total Cost* Low Cost $6 $1,500 Average Cost $10 $2,500 High Cost $20 $5,000.
What is the best material for fascia boards?
Typically for fascia boards, cedar and redwood are popular choices given their resistance to rot from excessive moisture. However, if you prime and paint the fascia, then fir, spruce, and pine can also make beautiful choices from a design standpoint.
Can you use Hardie board for fascia?
HardieTrim board is a decorative non-load bearing trim product. Do not use HardieTrim to replace any structural component. HardieTrimboards can be fastened directly over a 2x sub-fascia or directly to rather tails.
What is the standard size of fascia board?
Fascia Board Sizes Fascias are typically made from 1-inch material, with the width being enough to cover the rafter width. Typically rafters will range from 2×6 to 2×8, although some are larger depending on the roof construction. Therefore, the more common fascia board sizes are 1×6 or 1×8.
Does fascia board go under roof sheathing?
Measure up the rafter 45-3/4 inch from the cut end of the truss tail and snap a line along the trusses. This indicates the upper edge of the first row of roof sheathing—leaving enough overhang that the subfascia and fascia will tuck neatly underneath when the time comes.
How long do fascia boards last?
Well installed and maintained wooden fascia can last for up to 20 or 30 years, before they start deteriorating. Although some might need replacing within 5 to 10 years.
How do I fix my soffit and fascia?
Soffit and Fascia Repair Remove Shingle Mold. Pry the narrow shingle mold from the fascia using a flat bar. Remove Rotted Fascia. Remove the rotted section of fascia. Remove Old Soffit. Pull down to remove the old soffit. Remove Rotted Rafter. Attach Cleat. Attach New Rafter. Seal Replacement Soffit. Attach Replacement Soffit.
Is drip edge nailed to fascia?
The correct placement of a roof drip edge is on top of the roof’s exterior cover directly between the sheathing and the fascia board, which forms a drainage gap between the drip edge and the fascia board. As a result, the drainage improves water flow and protects the roof from potential water damage.
Should drip edge be nailed to fascia?
A vertical drip edge lip extends down roughly 1 5/8″ and as Steve points out, should not be set tight against the fascia board or water may run behind the gutter and down the fascia, inviting leaks and rot.
What are soffits?
The soffit is part of the overhang where your roof meets your siding. When rain or snow hits your roof, it runs down, and the overhang allows the water to flow away from your house. The fascia is the attractive board along the side of the overhang and the roof that helps your roof appear finished.
What is another name for fascia board?
The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
Should fascia board be treated?
Should the fascia board be pressure treated? – Quora. It’s not necessary to use pressure-treated lumber for fascia. In fact, most planking sold for fascia is not pressure treated. However, it is vital that the fascia be primered and completely painted with a good quality exterior enamel or acrylic paint.
Can PVC be used for fascia board?
Obviously the biggest reason for using a PVC trim board is long term maintenance combined with traditional architectural appeal. PVC trim boards will not rot, twist, split or warp. In addition you can leave it unpainted if you like or paint it to match a certain color scheme.
Is Hardie trim discontinued?
While your preferred siding brand may have discontinued production for some of their products, you should not be afraid as many options are available. For instance, recently, James Hardie has discontinued their trim supply in 2021 for the Pacific Northwest.
Can cement board be used as fascia?
Soffits and fascia board We used fiber cement board to close in the soffits and cover the fascia of the house. Any rotted fascia boards should be replaced prior to covering. The fiber cement board, although durable, is not structurally adequate to support the eaves on its own.
