Table of Contents
Can you bypass a thermocouple on water heater?
Realistically, you have just disabled the thermocouple, but you can also reach in and unclip it from its holding bracket where it meets the pilot light. In most cases it will be held on with a gravity clip, but some are held on with a screw that must be removed with a small screwdriver.
How do you bypass a thermocouple?
To bypass the thermocouple: Move the tilts switch wire aside. Remove your thermocouple from the heater using an 8mm wrench. Pull the valve housing aside using your 13mm socket wrench. Remove the valve using your pliers. Put your thermocouple back into position.
How do you reset the thermocouple on a water heater?
Press the small reset button in the center of the thermal switch. If it’s tripped, you may be able to hear it click. Even if you do not hear the thermal switch click, try lighting the pilot using the instructions on the water heater’s label. If the Status Light now begins to flash, the thermal switch probably tripped.
How do you bypass a thermal switch?
Locate and Bypass the Fuse The thermal fuse will look like a thin strip of white plastic with a wire coming out of each end. In order to bypass the thermal fuse, use electrical tape to tape the two ends together. The thermal fuse will then be bypassed. Turn the dryer on to a heat cycle for no more than 90 seconds.
How do I know if my thermocouple is bad on my water heater?
A worn out thermocouple is one of the most common gas water heater problems. When thermocouples wear out, the pilot light goes out, the burner won’t light, and you will have no hot water.
Does a thermocouple need to be in the flame?
Typically the thermocouple sensor is mounted right in the flame of the pilot light on gas fired heating equipment. But not all of these systems use a thermocouple. Some gas fired heating equipment relies on an electronic ignition to ignite the flame. Those devices generally will not use a thermocouple.
What causes a gas water heater pilot to go out?
Your thermocouple senses when your pilot light is burning. If it senses that your water heater pilot light keeps going out, the thermocouple will shift off the gas supply to the heater. Over time, thermocouples can malfunction, accumulate dust buildup, or the device can get bent away from the pilot light’s flame.
Why won’t the pilot stay lit on my wall heater?
The Pilot Won’t Stay Lit A pilot that won’t stay lit could be the result of a blockage in the pilot tube. Turn off the gas, clear the tube with compressed air, and relight the pilot. If that doesn’t work, you may need to call a repairman to come and install a new thermocouple.
Is there a reset button on a gas hot water heater?
A water heater reset button, usually red, is located in the center of the limit switch just above the water heater thermostat. The water heater limit switch is a safety device that will shut the power down to the water heater if something malfunctions and the water gets to hot.
Where is the reset button on the water heater?
Somewhere on your electric water heater, you’ll find a reset button. It’s usually red and often located near the thermostat. It may also be hidden behind a removable metal panel on the unit—and then behind some insulation. Once you find the button, push and release it.
Can a thermocouple be cleaned?
Yes, you can clean a thermocouple, but the task must be done with a light touch. Remove the thermocouple from the process assembly, using a steel wool or emery cloth, lightly clean the tip removing any build up. Cleaning a thermocouple is not a fix for an issue, such as inaccurate readings.
Where is the thermal switch on a water heater?
On a typical residential gas water heater, the TCO is a manually resettable thermal switch located on the front of combustion chamber door. The TCO is integral with the thermocouple or thermopile depending on type of gas control valve.
Do water heaters have an on/off switch?
The on/off is on the breaker panel. You can add a separate on/off switch if you want to. Gas water heaters have a gas shutoff near the unit. And they have an on/off/ pilot only position on the gas control..
How do you troubleshoot a thermocouple?
Importantly, always make sure the tip of the thermocouple is directly in the pilot flame. If the tip is in the flame, you have held the nob on the gas valve down for longer than a minute, the pilot flame is strong and steady, and the pilot still does not stay lit, then you likely have a problem with the gas valve.
How long should a water heater thermocouple last?
Thermocouples can last up to 10 years if properly installed and maintained, while furnaces can last 15-20 years, although either may wear out sooner in multifamily units.
What happens when thermocouple goes bad?
Normally when the thermocouple malfunctions or isn’t working, it simply shuts off the gas to your heater. This is important, particularly if the pilot light is out, because it prevents harmful gas from leaking into your home.
