Table of Contents
What is the formula for stair stringers?
There are several formulas for calculating the ratio between rise and run; the simplest is Rise + Run = 17 to 18 inches. Using a target run of 10 inches, the rise/run ratio is well within the “safe and comfortable” formula for this stair: 7 5/8 + 10 = 17 5/8 (Step 6).
How far apart do you put stringers for stairs?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How do I figure out how many steps I need?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
How many stairs stringers do I need for 6 foot wide?
This means you will need to install a minimum of four stringers on any stairway wider than 36”. Always check the maximum span for your decking material as it applies to stair treads.
Can you use joist hangers for stair stringers?
Use joist hangers to fasten the blocking. Pros: Allows for the use of all types of stair stringer hangers. The top of the stair stringer acts as the first tread instead of being flush with the deck’s surface.
Can I use 2×10 for deck stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What is the code for outdoor steps?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
What is a good rise and run for stairs?
Over the years, carpenters have determined that tread width times riser height should equal somewhere between 72 to 75 inches. On a main stair, the maximum rise should be no more than 8 1/4 inches and the minimum run should be no less than 9 inches.
What is the standard step height for stairs?
Riser Heights In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
How do you attach stair stringers to landing?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
How do you put a landing on stairs?
How to Build Stairs with a Landing Step 1: Finish Decking First. Step 2: Make Lower-stair Stringers. Step 3: Install Center Stringers. Step 4: Attach Stringers to Pad. Step 5: Attach Toe-kick. Step 6: Attach Stringers to Toe-kick.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
How many steps is 4 foot rise?
A four-foot high deck can have a range between 6 and 8 steps.
How tall is a 4 step Stringer?
Mendocino Forest Products Stair Stringer 4 step Redwood (Common: 48 in. x 12 in.; Actual: 1.5 in. x 11 in.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
