Table of Contents
How far apart should stringers be on deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What is the standard rise and run for deck stairs?
The stair treads should be at least 36 inches wide. Despite these minimum requirements, we recommend that stairs should be at least 48 inches wide so they don’t feel cramped. The maximum allowable stair rise is 7 3/4 inches, and the minimum stair rise is 4 inches.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
What is code for deck stairs?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
How do I anchor my deck stairs to the ground?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
What is the formula for building stairs?
Determining the Rise You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
How thick should stair treads be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
What angle should stairs be?
Standard stair angle by application Standard stairs have an angle of 30 to 50 degrees while steep stairs like alternating tread stairs and ship stairs have an angle between 50 and 70 degrees. Ladders have an angle range between 60 and 90 degrees.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
How deep should a footing be for stairs?
Dig a trench about 125mm deep for the footing for the first riser.
What is a floating staircase?
What are Floating Stairs? Floating stairs are a type of straight staircase that is self-supported. Because of the self-supported design a floating staircase requires no extra support between the underside of the staircase and the floor below or a wall.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Can I make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How far can 2×12 stair stringers span?
A 2×12 stringer has a maximum unsupported span of 6 feet. These stairs (7) are likely to deflect and cause the stringers to either pull loose from the framing or shear along the grain.
Do deck stair stringers need support?
To help resist both vertical and lateral loads, stringers require proper support and attachment at these bearing points. Without proper support, vertical loads (gravity) can pull the stringers down from their bearing points, while lateral (horizontal) loads can pull the stringers away from their bearing points.
