Table of Contents
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Do deck stairs need footings?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
What size boards do you use for deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
How far apart can stair stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
How do I anchor my deck stairs to the ground?
How to Anchor Deck Stairs to Concrete Use your jigsaw. Notch out the bottom front of the center stair stringers to accept a 2×4 base plate. Make sure your stringers are level. Fasten the base plate to the stair stringers with screws. Locked in place.
At what height do you need stairs for a deck?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
How deep should deck stairs be?
The maximum height of a single step is 7.75 inches, and all stair heights must be within 3/8 inch of each other, to keep the stairs regular. The depth (also called tread or run) of each step should be a minimum of 10 or 11 inches depending on the type of stairs.
What is the code for exterior stairs?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
Can you make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
Can you use deck boards for steps?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads. The stair treads should be at least 36 inches wide.
What is the formula for building steps?
You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
What should I put on the bottom of my deck steps?
Like any solid structure, your steps need a stable foundation. There are many options when it comes to footings for your deck steps, from concrete and gravel to patio stones and even grass.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
How do you secure stairs to a deck?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
Can I use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
