Table of Contents
How do you calculate stair stringers?
How do I calculate a stair stringer? Start by finding the overall height that the staircase will be. Decide the height or “rise” you’ll want for each step. Divide the total height of the staircase by the height or “rise” you want for each step.
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How far apart should stringers be on deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
Can I use 2×12 for stair stringers?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What size lumber do you use for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How many steps is a 4 foot high deck?
A four-foot high deck can have a range between 6 and 8 steps.
How long should a 2×12 stringer be?
cut stringers. The two most common cut-stringer defects that I see are overspanning and overcutting. The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Can you use joist hangers for stair stringers?
Use joist hangers to fasten the blocking. Pros: Allows for the use of all types of stair stringer hangers. The top of the stair stringer acts as the first tread instead of being flush with the deck’s surface.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
How high is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
What is the formula for calculating stairs?
How to Calculate Stairs – Example 1 450mm / 150mm = 3. This tells us that with a riser of 150mm we will need 3 risers/steps. 450mm / 2 = 225mm. Twice the Rise plus the Going (2R + G) should be between 550mm and 700mm. 2 x 150mm + 275mm = 575mm.
How do you calculate steps for a deck?
To determine the rise and run of the steps, measure the distance from the floor of the deck to the ground and divide that number by 7.5. The result will be the number of steps the staircase will need (e.g., deck is 112″ from the ground; 112/7.5 = 14.93. Round up to get 15 steps).
How tall is a 4 step Stringer?
Mendocino Forest Products Stair Stringer 4 step Redwood (Common: 48 in. x 12 in.; Actual: 1.5 in. x 11 in.
What is the standard step height for stairs?
Riser Heights In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
Are stairs 45 degrees?
No matter what the measurements are, the angle between them (treads and risers) will be maintained at 90 degrees. For example, if you were crazy and built a staircase with a 12 inch tread and riser, then the angle of the stringer to the floor would be 45 degrees. A more common angle is about 37 degrees.
How long should a 2×12 staircase be?
How to Use the EZ Stair Calculator. We suggest 10.5″ for 2×12 or 2 – 2×6 Treads. Treads may be cut to suit other widths.
What is the code for deck steps?
Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back. Stair treads must sustain a weight of at least 300 pounds in an area no more than four inches square.
How far should a stair tread hangover?
The tread nosing must overhang between 3/4” and 1-1/4” unless the tread is 11-inches or greater in depth. The stair lip improves safety by extending the horizontal space available for ascent and descent, and visually defines the step edge.
