Table of Contents
How do you build 3 sided deck stairs?
The trick to creating a three-sided staircase is to make bevel cuts on some of the stringers where they meet at the corners. The riser boards also get beveled, and the stair treads are mitered to help it all go together. The stairs have a post-and-railing system that matches the railing assembly on the deck itself.
How do you waterproof outdoor stairs?
For waterproofing wood stairs, choose a sealer designed for exterior applications. Look for the phrase “water repellent” instead of simply “waterproof.” A clear water repellant sealer will guard wooden stairs from water, UV rays and mildew. Reapply sealer once every year to maintain its water repelling ability.
How do I anchor my deck stairs to the ground?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What is the formula to build stairs?
Determining the Rise You divide the height by 7 inches; if, say, the floor-to-floor distance is 8 feet, 10 inches (or 106 inches), then you’ll need 15 treads (106 divided by 7 equals 15.14). Next, you divide the height by the number of treads (15 into 106), producing the exact tread height (7.06 inches).
What is the best angle for stairs?
Stair codes and guidelines prefer an angle of around 37° for normal stairways (the green area in our illustration) and around 7° for ramps (the yellow area in our illustration). Steeper slopes or angles are permitted for stepladders in certain applications as you can see in the illustration.
What size wood do you use for steps?
Stair treads may be made of a single 2×12, but are often made of two decking boards or 2x6s. A stringer is a wide board, usually a 2×12, that runs at an angle from the landing pad to the deck framing and supports the treads.
How do you seal outdoor concrete steps?
Here’s a step-by-step summary of how to seal concrete: Remove all oil, grease, stains, dirt, and dust from the concrete. Strip any existing sealer from the surface. Open up the concrete with an etching solution. Apply a thin coat of sealer using a roller or sprayer. Wait for the first layer of sealer to dry.
Do the bottom of deck stairs need footings?
Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground. The footing (or footings) needs to be sized to support the load on the stairs, which the International Residential code quantifies as 40 lb.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Do I need a concrete pad for deck stairs?
Building codes generally require that exterior stairways have a concrete footing or foundation. Without the foundation the steps will sink, heave or tilt to one side. This article shows how to build a 4-in. thick slab that will serve as a foundation for a set of deck steps.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
What is code for deck stairs?
Requirements for Deck Stairs Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back.
What type of wood is used for deck stairs?
Treated lumber is ideal for projects such as deck stairs, basement steps and steps leading to back porches and outbuildings. Treated lumber is strong and long lasting. It is always a smart choice for ground contact because it resists rot better than most wood products.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
Can you make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How far apart can stair stringers be?
Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers. The maximum 18-inch spacing presumes treads of 5/4-inch wood decking or 2-by stock.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What is the standard step height for stairs?
Riser Heights In the United States, the step height standard should be between 7 or 7 ¾ inches at the most, and no less than 4 inches. You should follow other measurements if given by local building codes. In Canada, the maximum step riser height is 8 ¼ inches.
How do I calculate how many steps I need?
Divide the rise by 6 or 7 inches (15 or 18 cm) to find the total number of stairs. For larger stairs, divide by 6 and for smaller stairs, divide by 7. The total you get is how many stairs your future staircase will have so you can plan accordingly.
What is a good rise and run for stairs?
Over the years, carpenters have determined that tread width times riser height should equal somewhere between 72 to 75 inches. On a main stair, the maximum rise should be no more than 8 1/4 inches and the minimum run should be no less than 9 inches.
