Table of Contents
How far can deck stairs span?
The minimum recommended size for a deck stair stringer is 2×12, which has a maximum recommended unsupported span of 6 feet. Often this maximum span is dangerously exceeded, resulting in overspanned stringers that will deflect and cause the connection at the deck to pull loose and fail.
How long can deck stairs be without a landing?
A flight of stairs should not rise vertically more than 147 inches without a landing. An intermediate landing is a small deck, and should be built as such, including appropriate footings, posts, and bracing.
What is the maximum distance between stair stringers?
Stringers should be spaced no more than 36 inches apart from each other for maximum stair support, according to the International Association of Certified Home Inspectors. However, local residential codes may vary slightly, so check the building codes before building a staircase.
Can I use 2×10 for stair stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
Do deck stairs need risers?
Most high-end deck projects use closed risers to finish the stairs. They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
Can deck stairs land on grass?
Yes, it is a good idea to have a landing at the bottom of steps.
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
What is the code for deck stairs?
Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back. Stair treads must sustain a weight of at least 300 pounds in an area no more than four inches square.
How do you reinforce stringers?
One of the easiest methods of reinforcing your wood stair stringers is using 2×12 skirt boards along the outsides of your stairs. A skirt board is pretty much what it sounds like; triangular shaped wood that goes along the sides of your stair and hides all of the unsightly notched stringers and hardware.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
Can I use 2×12 for stair treads?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Are stairs 45 degrees?
No matter what the measurements are, the angle between them (treads and risers) will be maintained at 90 degrees. For example, if you were crazy and built a staircase with a 12 inch tread and riser, then the angle of the stringer to the floor would be 45 degrees. A more common angle is about 37 degrees.
What is the best wood for stair stringers?
LP SolidStart Laminated Strand Lumber (LSL) and LP SolidStart Laminated Veneer Lumber (LVL) are ideal for Stair Stringers because they surpass traditional lumber products in length, strength and consistency.
What accounts for roughly 90% of all deck collapses?
About 90% of deck collapses occurred as a result of the separation of the deck ledger board from the house, allowing the deck to swing away from the house. It is very rare for deck floor joists to break mid-span. Many more injuries are the result of rail failure, rather than complete deck collapse.
What is the standard rise and run for deck stairs?
The stair treads should be at least 36 inches wide. Despite these minimum requirements, we recommend that stairs should be at least 48 inches wide so they don’t feel cramped. The maximum allowable stair rise is 7 3/4 inches, and the minimum stair rise is 4 inches.
How many stringers do I need for deck stairs?
The number of stringers you need is a function of the width of the staircase and the tread material. Cut stringers can be spaced no more than 18 inches on center, so a 3-foot-wide staircase needs three stringers, and a set of slightly wider stairs (say 3 feet 6 inches) needs four stringers.
How wide should deck stairs be?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
What should I put on the bottom of my deck stairs?
Like any solid structure, your steps need a stable foundation. There are many options when it comes to footings for your deck steps, from concrete and gravel to patio stones and even grass.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
How thick should a concrete pad be for deck stairs?
Calculate the depth of the finished slab, including the concrete and the gravel base. Concrete is typically applied at a minimum of two inches, but I recommend a minimum thickness of 4 inches for a durable stair footing. With this type of application, both a fine and coarse aggregate are required.
