Table of Contents
Is it cheaper to make your own lattice?
Making your own lattice strips is more cost effective, and produces a better quality lattice strip than buying them in bulk at a major hardware store or even a reputable lumber yard.
What can I use under my porch instead of lattice?
If you don’t like the look of the lattice as a cover for under the porch, here are a few alternatives: Vertical wooden planks. Horizontal wooden planks. Wooden planks with a pattern or design. Rock porch skirting. Brick or stone. Alternative pattern vinyl lattice. Enclose the space.
Can I make my own lattice?
Wood lattice provides for a decorative solution to fencing or ventilation, but off the shelf it is often of low-finish quality, suitable only if painted or placed in nonprominent locations. With a few common tools and a little wood you can make your own lattice in no time.
Can you use screws on lattice?
Lattice screws have a sharp, pointed tip so you can install them without pre-drilling pilot holes. Installing lattice panels with screws takes a little more time and is slightly more costly than installation with nails, but it ultimately produces a longer-lasting outdoor structure.
Does lattice need a frame?
Lattice is typically purchased in either 24-by-48, or 48-by-96-inch sheets and cut to size depending on use. Framing is necessary after cutting.
How do you frame lattice under a deck?
Build the frame for enclosure. Nail 2x4s to existing posts to create the frame needed to secure the lattice panels. Run vertical 2x4s from the bottom plate to the existing deck. To install the lattice, measure vertically from the top of the panel (the bottom of the deck) to the ground. Screwing on Hinge.
What do you put around the bottom of a porch?
The area under the front porch (or mud room) is referred to as a Porch Skirt or Porch Apron. The porch fascia board or skirt board directly under the porch floor, transitions the porch to the porch skirt. The porch skirt, like the foundation, visually anchors the house to the ground.
How do you hide underside of deck?
Material Options for Hiding the Area Under Your Deck Lattice. Fence boards. Vinyl siding. Composite fascia boards. Stone faux.
How do I block the bottom of my deck?
If you want to completely block the underside of the deck, one option is to build a planter around the deck’s perimeter. It is a great way to soften the deck’s edge with plantings and is an interesting alternative to railings.
What type of wood is used for lattice?
The most common wood used for latticework is pressure-treated yellow pine, making the structure resistant to rot and insect damage. Lattice maybe painted or stained as desired. Higher-end structures make use of cedar, redwood, Douglas fir or mahogany – woods that are naturally rot-resistant and attractive in color.
How do you cut lattice panels?
Cutting Your Lattice Use a circular saw or jigsaw with a carbide tipped blade to cut the lattice. When you make your measurements, allow 1/4″ on either side to allow for expansion and contraction of the panels. If you have a slope, you will need to cut the lattice to match the grade.
How long does vinyl lattice last?
This type of lattice is considered permanent and can last up to 30 years. Most sellers guarantee it for a lifetime of use. This material requires virtually no maintenance, but it does have the highest price tag. This may not be an issue if you are using the lattice panels for a small project.
How do I put up lattice?
Cut the lattice panels to fit each frame using a sabre or circular saw. Lay the frames face down. Attach a piece of lattice to each frame using 1-inch pan head screws driven through washers. Allow a 1/ 4-inch gap on all sides between the edge of the frame and lattice.
Can you nail vinyl lattice?
When installing vinyl lattice be certain to use stainless steel nails or fasteners to secure your lattice sheets. This will prevent rust stains on your lattice.
Can you use a nail gun on vinyl lattice?
Deck Lattice: Steps You can also save a step by having the pros at your home center cut the panels for you. Attach the lattice panels to the open areas of the deck using your Arrow EBN320R. E.D. Electric Brad Nail Gun with 1-inch brad nails, securing at every criss-cross point in the lattice.
How do you secure a lattice to post?
Attach the framed lattice panel onto the posts below the deck with galvanized deck screws. Work with deck screws of a length that can penetrate the frame and bite into at least an inch of the post itself. Space the screws 16 inches apart, or four per deck post for a 4-foot-high lattice panel.
What is the best tool to cut vinyl lattice?
The best way to cut vinyl lattice is to use a circular saw and a cutting blade. Most of the people who usually need to do it regularly, suggests using a circular saw and a sharp and new cutting blade. You can also use a trim saw or a handsaw.
What screws to use with lattice?
Use #8 stainless steel sheet metal screws to maintain the beauty of your project. Place fasteners 24″ apart for best results.
How do you anchor a freestanding trellis?
Anchor a trellis with ground spikes by driving 12- to 18-inch wood or metal stakes into the ground with a rubber mallet, leaving about 6 inches of each stake above ground. Place the trellis against the stakes and secure it to the stakes with plastic zip ties or sturdy rope.
How do you attach lattice cap to lattice?
Attach caps and divider moulding to lattice with 1-5/8″ screws at the miter joints, from both directions (see illustration). Drill small pilot holes near the edges of lattice, where screws are required, to ensure moulding and lattice do not split.
What type of wire is used for trellis?
Wire trellis structures are often made with stainless steel wire, galvanized steel wire, or aluminum wire, to minimize rust issues.
