Table of Contents
How far apart should stringers be on deck stairs?
Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
Can you use joist hangers for stair stringers?
Use joist hangers to fasten the blocking. Pros: Allows for the use of all types of stair stringer hangers. The top of the stair stringer acts as the first tread instead of being flush with the deck’s surface.
Can I use 2×10 for deck stringers?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
What lumber is used for stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has . 60 RET level.
What size lumber are stair stringers cut from?
Selecting stringer stock Stringers should always be cut from 2x12s. Notching smaller stock doesn’t leave enough wood to safely carry the loads of a stair. When ordering stringers, allow about 14 inches of stringer length for each step. Look for straight stock with as few knots as possible.
What is the code for deck posts?
Beams and girders must be made from laminated two-by-fours, two-by-sixes or two-by-twelves rather than solid lumber, and deck joists can’t cantilever more than 24 inches beyond a support beam or girder. All vertical support posts must be made from six-by-sixes, and posts can be no taller than 14 feet.
Do deck stair stringers need support?
To help resist both vertical and lateral loads, stringers require proper support and attachment at these bearing points. Without proper support, vertical loads (gravity) can pull the stringers down from their bearing points, while lateral (horizontal) loads can pull the stringers away from their bearing points.
How far can 2×12 stair stringers span?
A 2×12 stringer has a maximum unsupported span of 6 feet. These stairs (7) are likely to deflect and cause the stringers to either pull loose from the framing or shear along the grain.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
How far should a stair tread hangover?
The tread nosing must overhang between 3/4” and 1-1/4” unless the tread is 11-inches or greater in depth. The stair lip improves safety by extending the horizontal space available for ascent and descent, and visually defines the step edge.
What should deck stairs rest on?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Do deck stairs need a footer?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
How do you reinforce stair stringers?
One of the easiest methods of reinforcing your wood stair stringers is using 2×12 skirt boards along the outsides of your stairs. A skirt board is pretty much what it sounds like; triangular shaped wood that goes along the sides of your stair and hides all of the unsightly notched stringers and hardware.
What is the best wood to use for outdoor steps?
Two types of wood widely considered the best for outdoor building of any kind are redwood and cedar. This is because they are both naturally resistant to weather damage, are easy to work with, and have a reputation for being long lasting wood even when not treated, stained, or painted.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
How tall is a 2 step Stringer?
Size:2 In. Step stringers are cut for 2″ X 12″ Treads, and have a 7″ Rise.
