Table of Contents
How do you build a set of steps for a deck?
What is code for steps on decks?
Stair rails on decks should be between 34 inches and 38 inches high, measured vertically from the nose of the tread to the top of the rail. Treads must be at least 10 inches deep, measuring from front to back. Stair treads must sustain a weight of at least 300 pounds in an area no more than four inches square.
What size lumber is used for stair stringers?
The stair stringers are essentially the backbone of your staircase. Always use straight, high-quality, pressure-treated 2x12s for stair stringers. If you are planning on resting the stringer on the ground, make sure the wood has .
How do I anchor my deck stairs to the ground?
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How tall is a 5 step Stringer?
Stair Stringer-5 step Redwood (Common: 60 in. x 11 in.; Actual: 1.5 in.
Are risers required on deck stairs?
Most high-end deck projects use closed risers to finish the stairs. They also are often in violation of IRC code for decks over 30″, which maintains that they meet the same requirements as guardrail infill. Stair risers may not have openings present that would allow a 4” diameter sphere to pass through.
Do I need footings for deck stairs?
SAFE, SUPPORTED STAIRS: Deck-stair construction varies, but the general requirements are consistent: proper footing support, and an adequate landing. Regardless of the stair run and number of treads, the stairway needs a footing at the bottom to support the stringers—they can’t just rest on the ground.
Do you need a railing for 3 steps?
A: Editorial Adviser Mike Guertin replies: Since your stairs will have only three risers, you don’t need to install a handrail. That said, it’s important to count the number of risers accurately.
What is the formula for calculating stairs?
How to Calculate Stairs – Example 1 450mm / 150mm = 3. This tells us that with a riser of 150mm we will need 3 risers/steps. 450mm / 2 = 225mm. Twice the Rise plus the Going (2R + G) should be between 550mm and 700mm. 2 x 150mm + 275mm = 575mm.
What is the best wood to use for outdoor steps?
Two types of wood widely considered the best for outdoor building of any kind are redwood and cedar. This is because they are both naturally resistant to weather damage, are easy to work with, and have a reputation for being long lasting wood even when not treated, stained, or painted.
How deep should outdoor steps be?
The 7-11 rule is one that’s frequently used (maximum riser height of 7 inches and minimum tread depth of 11 inches). Risers should also be at least 4 inches in height.OUTDOOR STEP HEIGHT. When riser height is: Tread depth should be: 5″ to 5-1/2″ 16″ to 17″ 6″ to 6-1/2″ 14″ to 15″ 7″ to 7-1/2″ 10″ to 11″.
What is the code for exterior stairs?
Exterior Stair Construction The rise of the stairs should be between 125 mm (5”) and 200 mm (8”). This is measured from top of a tread nosing to the top of the next tread nosing or landing. The run should be between 210 mm (8 ¼”) and 355mm (14”). Unit run is measured from face of nosing to face of nosing.
Are stair stringers 2×10 or 2×12?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
What should I put on the bottom of my deck stairs?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.Footings with Different Deck Stair Landing Options Concrete landing pad. A wood box-type landing pad. Crushed stone. Patio Blocks.
Can I use joist hangers for stair stringers?
This will reinforce the stair stringer to rim joist connection and distribute the stair weight more evenly onto the deck framing. Cut them to fit the space perpendicularly between the rim joist and the next interior joist. Use joist hangers to fasten the blocking.
Can you make stringers out of 2×10?
Pressure-treated or cedar 2×10 or 2×12 can be used depending on the depth of the cut-outs you’ll be using. By code you will need a minimum of 3-1/2″ of material left on the stringer after the cut-outs and that area should also be free of large knots which would weaken the stringer.
How thick should a stair stringer be?
According to general specifications, your stair riser thickness should be no less than ½”. In fact, many professionals recommend risers with a thickness of ¾”. It’s also important to note that if you do build a closed riser staircase, your stair treads will need to have a note as well.
Do deck stairs have to land on concrete?
Stair landings must be at least as wide as the stair and at least 3 feet deep. On the other hand, solid, flat, and stable materials, such as concrete, flagstone, pavers, or brick, can be installed with a measurable slope and will not usually shift under the weight of an off-balance person completing a stairway descent.
