Table of Contents
Do I need a box for recessed lighting?
Types of Devices That Don’t Need Boxes The first clue that a device is designed to be used without a junction box is that it has its own complete housing. Common examples of electrical devices that require no junction boxes include: Recessed lights (“can lights”) Bathroom ventilation fans.
How far apart should recessed lights be?
A good general rule for placement is to divide the height of the ceiling by two. The result is the amount of space to leave between each light. For example, recessed lighting spacing for an 8-foot-high ceiling would be 4 feet between each light. This will provide good spacing for general room lighting.
Is recessed lighting outdated?
The one reason why recessed lighting is timeless because they offer the flexibility to change the finishes later. You have a can in your ceiling that stays forever. However, the finish may become outdated and can be purchased in different colors and styles to suit your needs. You can change them as often as you like.
What wood is used for soffits?
Although unsanded and touch-sanded grades of plywood are often used for soffits, optimum appearance and finish performance is achieved by using panels with Medium Density Overlay (MDO), or textured (such as APA 303 Siding) or sanded A-grade faces.
What is the difference between F Channel and J channel?
F channel is usually attached to beams or studs of the house, along the underside of the roof overhang. It provides a sort of shelf where the ends of the soffit pieces rest. If you choose J channel, you’ll have to install twice as many pieces, both to hold up the soffit and to cover the edges.
What is a soffit box?
A soffit is an exterior or interior architectural feature, generally the horizontal, aloft underside of any construction element. Its archetypal form, sometimes incorporating or implying the projection of beams, is the underside of eaves (to connect a retaining wall to projecting edge(s) of the roof).
How do you install an electrical soffit box?
If it’s aluminium/plastic soffit covers, you’ll have to remove the section where you’re installing the receptacle. Install proper bracing (a simple 2×4 between the rafters should be fine), and attach the electrical box to it. Then mark, and cut a hole for the electrical box in the soffit cover.
Do LED lights need junction box?
If you’re wondering how you install a light fixture without an electrical box, the short answer is that you don’t. You can’t install a light fixture without a junction box, but the fact that there’s no box at the spot where you want to install the light doesn’t mean you can’t install the light.
Does a junction box have to be attached to a stud?
They don’t need to be fastened to a stud, so you can install them anywhere.
Do I really need a junction box?
You’ll need a junction box if you can’t make the connections inside an existing electrical box. You should install the box with the opening facing out from the wall so all the wires inside are accessible. Like any electrical box, it should be installed so that the edge of the opening is flush with the wall.
How many can lights in a 20×20 room?
If you have a center light fixture, you should be able to use 4 inch line voltage cans or low voltage for supplemental lighting. I would go with at least 8 three inch cans for a 20 foot room.
How do you stagger recessed lighting?
The typical rule is to place the lights the same number of feet apart as the bulb’s diameter, in inches. So a bulb with a four-inch diameter should be four feet away from the next light.
How many lights can I put on one switch?
There is no limit to the number of lights on a circuit. The load of the fixtures is what determines how many lights a circuit can accommodate. A conventional 15A circuit can have up to 1400W of lighting loads connected to it. A 1400 Watts lighting load can accommodate one 1400W fixture or fourteen 100W fixtures.
Why is recessed lighting bad?
Used properly, recessed lights are sleek, unobtrusive fixtures that can be good problem-solvers. Used improperly, they can waste electricity, provide poor lighting and cause your heating and cooling bills to go up. Kitchens are common places where recessed lighting fixtures are used.
How much should it cost to have recessed lighting installed?
Recessed Lighting Cost Expect to pay between $100 to $480 per fixture, or $360 on average, when having recessed lighting installed by a pro. At the average price, the project runs about $2,160 for six fixtures. The total varies depending on the type of housing, trim, and bulbs you select.
What is the difference between can lights and recessed lights?
Recessed lights, also known as can lights, are described as metal light housings installed in the ceiling for a sleek look that gives you back your ceiling.
What can I use instead of soffit?
Soffit Material Options Wood. Wood is one of the oldest materials used for soffits, and like wood siding is still around today. Vinyl. Vinyl soffits are another option that emerged along with vinyl siding in the 1950s. Aluminum. Fiber Cement.
What size plywood should I use for soffit?
Soffits are generally made from AC plywood, the thickness depends on your soffit framing, and the distance the soffit will be spanning. If your soffits are narrow, and the framing is on 24″ centers, then you could go with 3/8″ AC ply. But for soffits that are 2ft wide or more, I’d recommend 1/2″ AC ply.
Are wood soffits bad?
Wood soffits are often the victims of mold, mildew, and fungus, due to roof leaks. These could potentially cause respiratory and other health issues due to spores in the air. In addition to mold and mildew, fungi can break down the fibers in the wood, leading to the wood crumbling, known as dry rot.
