Table of Contents
Can you build a platform for a tub?
Constructing the platform for a tub isn’t difficult, but it requires accurate measuring and cutting. This project is very straightforward for a carpenter, so you may be well served to hire out this phase. Check the height of the platform that your tub requires and calculate the height of the platform wall studs.
What do you put under a bathtub for support?
Both regular thinset mortar and floor leveling compound are suitable. A series of strategically placed piles is easier to control than a full bed, and it provides comparable support for the tub. Level the subfloor in the alcove where you intend to install the bathtub, and cut the hole for the drain.
Can you build around a freestanding tub?
“Freestanding tubs can work in many different types of bathrooms. The key is to make sure they work with the proportions of the space. “It’s important to have ample space around at least three sides of a freestanding tub. When freestanding tubs are confined on multiple sides, they tend to make a space feel smaller.
Do you put cement board under bathtub?
The best approach when installing cement board or other tile backer around a tub is to keep the cement board out of the lip area. above the lip of the tub. Then apply a generous amount of thin-set to the bottom bathtub tile and position it 1/8 in. above the tub.
How much support does a bathtub need?
The floor framing for bathtubs requires special attention. You must consider all of the weight the floor joists must be able to support. A standard bathtub can hold between 40 and 60 gallons of water.
Can you build your own bathtub?
Building your own bathtub is not an inexpensive or easy process, but it can be done. Tubs can be built from wood, concrete or tile-covered masonry. A homemade tub will generally cost more than a purchased tub, but can be shaped to fit an unusual space or made longer, taller or wider than standard tubs.
How do you build a drop in tub surround?
Drop in tub surround with full access Step 1: Frame out surround. Step 2: Install proper substrate on framing. Step 3: Install finished surround material. Step 4: Finish top deck. Step 5: Place tub and Shim/level. Step 6: Secure the bottom of the tub. Step 7: Install drain/overflow. Step 8: Install high flow tub filler.
What is a Roman tub?
Today’s version of the Roman soaking tub consists of a tub where the filler spout rises off of the deck instead of through the walls of the room or the wall of the tub. Roman tubs got their name from the baths built by the Romans, which were bathing pools that you stepped down into.
Do I need to reinforce floor for tub?
In general, unless there is something wrong with the joist spacing or the wood has rotted, the framing in most houses should be able to support a standard size cast iron tub with no problem. Larger cast iron bathtubs may require more joist or subfloor reinforcement for the tub to be safe to use.
Can I use expanding foam under bathtub?
Yes, expanding spray foam can be used under a bathtub. It can reduce coldness and flex in an existing install, but an improper application can result in additional problems. It’s important to understand that the tried-and-true best practice for preventing flex in a newly installed bathtub is with a mortar slab.
What is the standard depth for a bathtub?
The standard tub size for an alcove fixture is 60 inches long, 32 inches wide, and 18 inches deep. Small alcove tubs are available for smaller bathrooms, which are anywhere from 48 to 55 inches in length.
What size is a 2 person tub?
A medium sized two person bathtub starts at around 66.9 inches long with a width of 33.5 inches and a height of 22 inches. The largest of the medium sized bathtubs comes in at 70 inches with a width of 35.4 inches and a height of 22.5 inches.
How far off the wall is a tub drain?
Bathtub Drain Measurements The drain hole should be a minimum of 12 inches away from the wall and 9 inches in scope. To rough in the drain, use a 1.5-inch pipe.
How far from the wall should a freestanding bath be?
How far should the distance be between freestanding tub and wall? The distance between your tub and wall should be between 15-18 inches or at least 1 foot.
How much space do you need around a free standing bath?
A freestanding bath should have no less than 6 inches of space surrounding all angles of the tub. By following that guideline, you can ensure your freestanding bath has a comfortable access point, and won’t appear cramped in your bathroom regardless of its design.
Can you put a tub on top of tile?
You can install a bathtub over the existing floor tile. However, the preparation of the space is just as important as the installation. You must ensure the subfloor under the tile is strong enough to support the weight of a bathtub.
