Table of Contents
How do you make a bookshelf step by step?
How to Build a Bookshelf in 8 Steps Step 1: Cut the Legs, Shelves, and Supports. Photo by Kolin Smith. Step 2: Attach the Supports to the Legs. Step 3: Assemble the Box. Step 4: Level the Bookcase. Step 5: Plumb the Bookshelf. Step 6: Attach the Kick Board. Step 7: Scribe the Trim to Fit. Step 8: Apply Nosing to Shelf Faces.
What angle do you cut corner shelves?
Use a tape measure and carpenter’s square to mark the length of the shelf boards. For the outer ends of the shelves, cut across one end of each board at a 45-degree angle, with the angle of the saw’s blade also set to 45 degrees for the mitered edge strip (this is called a compound cut).
How do you support a shelf in a corner?
Corner shelving should be fixed to the support battens – with the shelf in position, mark underneath the side of the supports onto the shelf. Drill a hole halfway between the marks and the edge of the shelf to take a small screw, and countersink the top side of the shelf if necessary.
How do you measure a corner bookshelf?
Multiply the surface area for one shelf by the number of shelves. For example, if you have four triangular shelves, multiply 80 * 4 = 320 inches for the entire corner shelf unit. If you have three quarter-circle shelves, multiply 50.24 * 3 = 150.72 inches for the entire corner shelf unit.
How do you join two pieces of wood lengthwise?
What you need to do to achieve this one is to butt the pieces and mark the dowel positions accordingly. Position the doweling jig over the top of the mark and start drilling your holes. You now need to spread the glue over one piece within the holes and insert the dowels. Glue the end grain and house the other piece.
How do I make a corner template?
How to Make a Cardboard Template for a Corner Shelf Place a large piece of cardboard into the corner. Measure both sides of the cardboard from the corner. Place a straightedge on the cardboard at the point where you made the marks. Place the cardboard on a worktable. Insert the triangle into the corner.
How thick should bookshelves be?
Use 3/4-inch thick materials for shelves and bookcase structure. If you’re using hardwood solids, it’s OK to boost the thickness to 1 1/4 inch for almost unlimited support. This type of shelf looks more like a mantel and is expensive, but adds the opulent look of craftsmanship.
What wood is used for shelves?
If you are making shelves where the color and grain of the wood is an important part of the design, look for oak, maple, or cherry plywood—these options will still offer durability, but will help keep costs down compared to with non-manufactured hardwoods of the same species.
How do you make a corner cabinet more useful?
These smart tips from organizing experts on how to best utilize your corner cabinets. Stash less-used items in the back. Use bottom corner cabinets as appliance garages. Or consider storing garbage and recycling. Resist the urge to overfill. You don’t need fancy organizers.
How do you find the angle of a corner cabinet?
Measuring Around Corner Cabinets One corner of each board must contact the joint between cabinets. Make a mark where the two boards intersect, then draw a line from that mark to the corner that contacted the cabinet joint. This line is the bisection angle you’ll need to cut crown molding accurately.
Is it hard to build a bookcase?
In-the-wall bookcases are elegant, but they can be difficult and expensive to construct. Basically consisting of three plywood boxes fitted with a hardwood face frame, this piece looks built-in because it spans from wall to wall, and is trimmed with molding at the ceiling and floor. I used 3/4-in.
What is the backing of a bookshelf called?
I’ve used 1/8″ luan to back a bookshelf before and it did well. It’s also known as “door skins”.
What is a rabbet joint?
A rabbet (American English) or rebate (British English) is a recess or groove cut into the edge of a piece of machinable material, usually wood. A rabbet can be used to form a joint with another piece of wood (often containing a dado). Rabbet joints are easy to construct and have good appeal to them.
How do you stabilize a bookcase without the back?
If it has a backing, drive 3-inch screws through the backing into the studs behind the bookcase. Use washers with the screws to distribute the load. Alternatively, if there is no backing, affix 1-inch metal corner brackets to the studs and the underside of the top shelf or the sides of the bookcase.
How do you stack two bookcases?
Place three C-clamps spanning across both bookcases evenly spaced vertically from top to bottom. One side of the clamps will fit in one bookcase, and the other side will fit into the other bookcase. Tighten the clamps securely to bond the two bookcases together.
Can you stack two Billy bookcases?
BILLY bookcases are built with a stackable design that allows you to attach new units whenever you need additional storage, just decide on what height suits your space best. Every model in the BILLY series also features adjustable shelves so you can fit anything from books to trophies, and everything in between.
What angle do I cut for a corner shelf?
Make a 22.5-degree “rip” cut, angle up, along the front edge of the shelf using a table saw. On the top side of the shelf, create an 1/8-inch deep dado about 1-1/4 inches out from the wall. This is easily done on the table saw by making two shallow cuts side by side.
How thick should plywood be for shelves?
The most common size used in shelving is a 3/4 inch thickness. Cabinetry, furniture, and smaller decorative projects might generally use a combination of 1/2 and 3/4 and occasionally 1/4 inch.
