Table of Contents
It depends what type of bleed screw is fitted to your radiator. For radiators with a slotted bleed screw, a simple screwdriver represents an ideal alternative to a bleed key. Just insert the screwdriver into the slot and turn it in a counter-clockwise direction to bleed the radiator.
How do you get air out of radiator without key?
The most popular alternative to a radiator key is by using a flat head screwdriver. Most modern radiators manufactured over the last 5 – 10 years will have a small indent allowing for a flat head screwdriver to be inserted into the bleed plug.
How do you bleed a radiator without a bleed valve?
Bleeding a Radiator With a Towel Rail or Compression Joint Turn off your heating and give the radiators time to cool down. With a towel to hand, loosen the compression joint where the towel rail joins the radiator. Once the hissing stops, retighten the valve with the wrench. Turn the heating back on.
How do you bleed a steam radiator without a key?
When you bleed the radiator without the key, you can simply use an Allen key (or sometimes called an Allen wrench) of the same size. No Allen keys in the house? A flat-head screwdriver often makes a suitable Allen key substitute. If it’s slightly smaller than the socket, wrap duct tape around the head to make it fit.
Can you bleed a radiator with a screwdriver?
You can use a flathead screwdriver to bleed a radiator without a key. Place the flat head into the notches of the bleed valve. To bleed the radiator, turn anticlockwise to open the valve, and clockwise to close the valve. Remember to hold an old cloth or jug under the bleed valve to catch any escaping water.
What happens when you bleed a radiator and no water comes out?
If no water or air comes out when you bleed the radiator, then the valve could be blocked with paint. Insert the radiator key into the bleed valve and slowly turn it anti-clockwise (a quarter of a turn should be enough). You should hear a hissing sound as the air escapes.
Can I use pliers to bleed a radiator?
For example, you should avoid using pliers. However, no matter how careful you are, pliers can damage the screw, which could make it difficult to close the valve again or to bleed the radiators next time you come to do this job. You should also avoid using a cross head screwdriver.
Can I bleed a radiator when the heating is on?
You can’t bleed a radiator when the heating is on, as it may be too hot to touch. You could also get hot water spraying out of the radiator. Use your radiator key to turn the valve at the top of the radiator. Bleeding your radiators can cause the pressure to drop.
Can you bleed a radiator from the bottom?
We would recommend starting at the bottom and working your way up. In other words, bleed your downstairs radiators first, then move onto upstairs. Before you get stuck into opening your radiator valves, make sure your lovely home is protected from any dirty radiator water spillages.
Why is 1 radiator in my house cold?
Why is one radiator cold when the heating is on? One cold radiator usually indicates that either there is air in the system or there is a stuck valve within that radiator. To check if the valve is stuck, you can remove the rotatable head on the TRV to reveal a raised pin beneath it.
Do you bleed a radiator until water stops?
The average radiator should take no more than 20 to 30 seconds to bleed in full. This can vary with the size of the radiator and the amount of air trapped inside. Simply carry on bleeding the radiator until the hissing noise has stopped and water begins to run out of the bleed valve.
What happens if you let too much water out of a radiator?
Baird warns that letting out too much water is likely to introduce fresh water into the system, which can make the situation worse as fresh water contains a lot of air. He adds: “Some people also think if a radiator is cold on the bottom but hot at the top then it needs to be bled.
What size are radiator bleed keys?
Made of quality zinc alloy to ensure the key not easily broken, sturdy and reliable, which does not make the head of your radiator bleed valve into round. Size: 0.35in/9mm. The inside diameter of radiator key is 5mm.
Do you need to Repressurise a boiler after bleeding radiators?
Once you’ve bled the radiators, check the pressure gauge on your boiler. If the pressure is too low you’ll need to repressurise the boiler. If the system pressure is adequate, you can switch your heating on and check your radiators again to ensure that there are no remaining cold spots on the panels.
Which radiator do I bleed first?
The radiator to bleed first Making sure your central heating is switched off, you should start with a downstairs radiator that is the furthest away from your boiler. Work your way through the radiators getting closer to the boiler, then go upstairs and repeat the process.
How often should you bleed radiators?
With the production of air being a natural process of the central heating system, bleeding your radiators is one household task you’ll have to do on a regular basis. As a guide, bleeding them twice a year should keep them kicking out plenty of heat.
Why are radiators cold at the bottom?
Why your radiator is hot at the top and cold at the bottom Your radiators are most likely full of sludge. And when sludge accumulates within a radiator’s internal workings, it can prevent water from moving through them properly. Hence, you get the aforementioned cold patches.
