QA

Question: How To Bevel A Knife With A File

Can you make a good knife out of a file?

Once you’ve located a steel file, you need to anneal it. To do this heat it until it’s glowing yellow-orange either in a barbecue or fire pit and let it cool slowly. This helps soften the steel of the file. After it’s cool, sand the file and cut out the knife shape with a hacksaw.

What angle should a knife bevel be?

To make it easy, a 20 degree bevel angle is a good starting point. If properly sharpened, the 20 degree angle will work well for most knives. If you’re concerned about getting more performance from your knife you can fine tune the bevel angle to meet the specific needs of your knife.

How long does it take to hand file a knife?

Contrary to what you may have seen on TV, the average knife takes 15 to 20 hours of work. We hand-forge all of our blades, then grind them to refine the shape.

Do you have to temper a file knife?

In its hard and brittle state, the quenched blade will shatter like glass if dropped, it must be tempered before it is put to use. Tempering involves heating the blade to a non-critical temperature (350 – 450 F) to slightly soften the steel (I used a kitchen oven).

Can you grind a file?

You can grind down into the file a bit and test it this way to guarantee it’s hardened all the way through. Spark Test – Grind a bit of metal off the surface, then do a spark test on the file. It’s a lot less complicated than you think. High carbon steel makes LOTS and LOTS of sparks with few lines.

Should I convert my 20 degree knives to 15 degrees?

If you are using a given knife for heavier cutting or chopping if probably is best sharpened at 20 degrees. If you use a small or medium size knife only for light work such as paring, peeling, or light slicing you may prefer to sharpen it at 15 degrees in order to take advantage of its increased sharpness.

How do you calculate the bevel angle?

It is very easy to get the bevel measurement off just a little bit by not squaring it up. Move or copy the lines out in the open and draw a line between the end points. This creates a triangle surface on which we can measure the angle between the lines. The bevel angle is then this angle minus 90°.

What angle does spyderco sharpen their knives?

2. It doesn’t have infinitely adjustable angles. For sharpening knives, the stones are set at either 30 degrees (15 degrees on each side), or 40 degrees (20 degrees on each side).

How long does it take to learn knife making?

It takes at least three years to become a master bladesmith. After you have taken a few blacksmithing and bladesmithing classes, you can apply to become a master bladesmith through the American Bladesmithing Society.

How long does it take a blacksmith to make a knife?

How long does this whole process usually take? This depends on the type of knife and how experienced you are with the ways of making a knife. The forging can take anywhere from 1-4 hours for smaller knives. Then it will take 2-3 hours to harden and temper, depending on how many times you choose to temper your knife.

How long does it take to hand sand a knife?

Well-Known Member. A 3-1/2″ flat ground blade should not take more than 3-4 hours to hand sand depending on how good the grind was. Without being able to see the blade your asking about it is hard to tell what the problem is. It may be the steel or the heattreat,but should not be takeing that long.

What is the sharpest blade in the world?

Obsidian knife blades: overkill for slicing your sandwich. The thinnest blades are three nanometres wide at the edge – 10 times sharper than a razor blade. These are made by flaking a long, thin sliver from a core of obsidian (volcanic glass).

How sharp can a knife get?

The edge angle for very sharp knives can be as little as 10 degrees (for a 20° included angle). Knives that require a tough edge (such as those that chop) may sharpen at 25° or more. Different knives are sharpened differently according to grind (edge geometry) and application.

Can you heat treat a knife with a propane torch?

A propane (or MAPP gas) torch played evenly along the blade will get the job done. Try to get the heat color evenly across the blade. You don’t need to harden the entire knife blank. Just the blade is good enough.

Do you need a forge to make a knife?

Forging isn’t necessary to make a knife, nor will it produce a better blade (at least at the novice to intermediate skill level). Whether your goal is to devote many years to mastering the art of forging blades or you just want to hit hot steel, forging is great fun.

Can you make a knife without a forge?

You can make yourself a pretty good knife without a lot of expensive tools and without a forge. For the tasks that most of us use a knife for it is not necessary for the blade to be unduly hard. The quality of a larger rasp is usually good enough to make a workable knife without the need to harden it further.

What is the best material to make a knife blade out of?

Carbon steel grades with high amounts of carbon are desirable for knife making because they will give the blade the hardness and strength needed to hold up against impact and wear.

Why are Japanese knives so good?

Generally, Japanese knives are lighter, feel more balanced in the hand and feature steel that is harder, thinner and able to hold an edge for a longer time. These are exactly the reasons they’re so popular among professional chefs, and why they’re perfect for the precision tasks chefs do all day every day.

Why should a knife be washed after sharpening?

Yes, you should clean after sharpening, which is not the same as honing. No, after honing, it’s not necessary. By sharpening, you take some metal off the edge of the knife to create an edge.