Table of Contents
Attach the stringers to the deck using angle brackets and 3” galvanized deck screws. Cut a 2×6 board to fit snugly between the two stringers at their base. This will be used to fasten the stairs to the concrete pad. Place the board between the stringers and attach to stringers with 3” galvanized deck screws.
Do stair stringers need hangers?
To attach stair stringers to a deck, you must use a metal stair stringer hanger. End-nailing, toe-nailing, or screwing stringers to a header is not allowed per the International Residential Code. Metal hangers must use appropriately sized nails or fasteners specific to the stringer hanger manufacturer.
What do deck stringers sit on?
Your stair stringers will rest on your landing pad, but you should include a base plate. A bearing block is typically a 2×4 that connects your stringers.
How do you reinforce stair stringers?
One of the easiest methods of reinforcing your wood stair stringers is using 2×12 skirt boards along the outsides of your stairs. A skirt board is pretty much what it sounds like; triangular shaped wood that goes along the sides of your stair and hides all of the unsightly notched stringers and hardware.
Can you use joist hangers for stringers?
This metal bracket supports the stringer and holds it on the framing. Stringer hangers look like joist hangers and function in the same way. Most local code authorities require the use of stringer hangers, and using them makes installation easier.
Should I use nails or screws for stairs?
The answer is both. You should use nails to attach the deck’s joists and stair stringers to its framing. You should use screws to attach decking and railings to the framing.
How many stringers do I need for deck stairs?
Deck Stair Basics Deck stairs are typically made from 2 x 12 stringers spaced about 12 to 16 inches apart. They rest on a solid foundation and are attached to the deck with hangers. They have risers (also called toe kicks), treads and railings. The stairs should be at least 36 inches wide.
How do I secure the bottom of my deck stairs?
How to Anchor Deck Stairs to Concrete Use your jigsaw. Notch out the bottom front of the center stair stringers to accept a 2×4 base plate. Make sure your stringers are level. Fasten the base plate to the stair stringers with screws. Locked in place.
Do you install risers or treads first?
When installing stairs, install the riser first, and then the tread. Start at the bottom of the stairs and work your way up, alternating risers and treads. The back of each tread will sit flush against the riser.
How do you fasten stair risers?
Install the first riser, beginning at the bottom of the staircase. Spread a thin coat of construction adhesive across the middle of the back of the riser. Attach the riser to the plywood with three nails spaced vertically along the left and right stringers, with a third line of nails along the center stringer.
What is the code for stair stringers?
Stair stringers should not span more than 13 feet and 3 inches (4039 mm) for a closed stringer. Cut stringers should not span more than 6 feet (1829 mm). Refer to the American Wood Council’s 2018 Prescriptive Residential Wood Deck Construction Guide for stringer spans.
Can I use 2×12 for stair treads?
It is acceptable and within building code guidelines to use either 2×10 or 2×12 dimensional lumber to create a set of stairs; however, a stair stringer should not be less than 3.5 inches wide at its narrowest point to provide adequate strength for the load the stairs will be supporting.
Can you connect stair stringers?
In some cases, longer runs of stairs call for connecting stringers at an intermediate support to avoid using long stringers that may twist. Other times, you may connect stringers to make the most of the materials you have on hand. Regardless of the application, the method used must ensure a reliable connection.
What is a stair skirt?
A skirt board on your stairs is a long, unbroken piece of trim just for your stairs. It either stands alone against the wall along the closed-end of your stairs, or you can run your regular baseboard along the top of it to create an unbroken line of trim from floor to floor.
What is a stringer Joist?
The stringer is the piece of lumber bolted to the house upon which the joists are fixed on or to. The spacing between the bolts depends on the size of the stringer and the span of the joists which are fixed on or to it.
Should a deck be built with nails or screws?
The Consensus: For a deck build it’s best to use a combination of nails and screws. Screws are superior for laying down the decking. They hold things flush better and have a better fastener/tensile strength, which keeps boards from popping up over time.
Are screws better than nails for decks?
For the decking boards, many agree that screws perform better than nails. They have better tensile strength and will less likely to pop out, which is a common problem in decking. Many also agree that nails are better used for the frame of the deck.
Do deck stair stringers need support?
To help resist both vertical and lateral loads, stringers require proper support and attachment at these bearing points. Without proper support, vertical loads (gravity) can pull the stringers down from their bearing points, while lateral (horizontal) loads can pull the stringers away from their bearing points.
How far apart should deck supports be?
Starting with your perimeter, mark the location of each deck post to locate the fitting position. In general, posts should be spaced no more than 8 feet apart. Some builders position them every 4 feet for a completely rigid frame. The maximum distance between footings is determined by the size of your joist material.
Do deck stairs need toe kicks?
The tread (or depth) of your steps should be ten and a half inches. The risers (or toe kick) must be between seven and eight inches high. A handrail is only required if your deck is more than thirty inches off the ground.
