How To Attach Shiplap

Do you screw or nail shiplap?

Nails are the best options when installing shiplap cladding. Trim nails are faster to install than screws since you do not need to predrill the material and won’t be risking causing unsightly splits.

How do you nail shiplap?

For shiplap with a smooth prepainted surface, like our Timeless nickel gap shiplap, you’ll want to use adhesive and nails. Instead of nailing through the face of the board, you’ll only nail through the flange of each board to avoid any visible nail marks that will affect the overall look of your wall.

What kind of nails do you use for shiplap?

We recommend using 16- or 18-gauge finish or brad nails. 1-½” to 2” in length should be sufficient. Both gauges are strong enough to hold the lumber securely, but small enough as to not leave a large hole on the face of the board.

Do you nail shiplap on every stud?

Once each board is in place, put a single nail at every other stud about an inch above the gap in the newly placed board. Be sure to nail on the same studs that you nailed the first board to, so that the nail pattern is consistent.

Should shiplap be face nailed?

We always recommend face nailing shiplap and tongue and groove when installing it on your walls, ceiling, and as exterior siding. Face nailing means that you shoot your nail at a 90 degree angle to the board through the flat (or face) of the board.

Should I fill the nail holes on shiplap?

Don’t forget to fill in any nail holes and gaps in the shiplap with spackle or caulk prior to painting. If you painted the shiplap prior to installation, fill in holes and gaps after the shiplap is in place and then touch up these areas with paint.

Can you use brad nails for shiplap?

Shiplap can be installed directly to sheet rock/drywall. Simply mark the stud locations for nailing the shiplap or you can apply a construction adhesive such as liquid nails. Use a nail gun with 18 gauge 1 3/4”long brad nails. Nail through the top flange which is the longer of the two flanges.

Can you just glue shiplap?

Tip: You can attach your shiplap boards with construction adhesive or nails or both.

Can you use Command strips on shiplap?

When you’re ready to start installing your shiplap wall, take two command strips and place on either side of a plank. Measure how far apart the strips are and place the other side of the strips (the wall side) on the wall equally far apart.

Can you glue shiplap to wall?

Shiplap planks can be fastened to walls either vertically or horizontally. Simply nail through the drywall directly into wall studs. You can use construction adhesive when installing on ceilings or over other surfaces, as long as they’re in good condition.

Where do I nail my shiplap cladding?

Begin at the bottom, ensuring that the first board is level with the lap that is adjacent to the wall, pointing upwards. For boards up to 150mm wide, use a single fixing located 25 – 30mm above the lower lap. Never nail through the lap joint.

Do you need nail gun for shiplap?

It’s also not uncommon for shiplap installers to use either a finish nail gun or a framing nailer. If using pre-manufactured shiplap, consult the board manufacturer for fastener specific requirements. Nails: The type of nail you use ultimately depends on the nail gun you’re using.

What kind of nails do you use for tongue and groove?

The two most common types of nails used for tongue and groove paneling projects are the brad nail or the finish nail. Brad nails are made of 18-gauge steel wire and because they are very thin nails, it makes them perfect for use with delicate material such as pine wood.

How do you attach shiplap to studs?

For installing standard 3/4″ shiplap on wood studs, use 2 and 3/8″ framing nails with a clipped head. If you will be screwing in place, use 2 and 1/2″ coated star-bit screws. The star-bits are the way to go – they never strip and install easily with an impact driver.

Should I start shiplap from top or bottom?

You can start applying shiplap either at the top or at the bottom of your wall. If you start at the bottom, gravity will work for you. If you start at the top, you’ll have to prevent each board from falling before you nail it in place.

How do you fill gaps in shiplap?

How To Caulk Seams On Shiplap Once you have installed your shiplap, run a bead of acrylic caulk (also known as latex caulk) along the seams where the shiplap ends butt up to a wall, inside corner or molding. Smooth out the caulk with a clean finger or rag so that the caulk fits neatly into the seam.

Is shiplap going out of style?

Shiplap is falling out of fashion. Once used to waterproof boats, shiplap siding became a trendy way to decorate interior walls in the 2010s. Street added that tile, plaster, rattan, or living walls of plants are becoming more popular this year, instead.

Do Brad Nails add strength?

Benefits of Brad Nails Brad nails are formed from a fine, 18-gauge wire, so they are smaller in diameter than finish nails and typically have less holding strength. In other words, 18-gauge brad nails provide a cleaner look than a finish nail without extra touch-up involved.

Can you use a brad nailer for paneling?

Nail guns save an amazing amount of time on large projects. A brad nailer — also called a tacker or a stapler — is intended for precision work. They are therefore well-suited to craft projects and for use in projects where the surface cannot be finished further, such as wall paneling.

What are Brad nails used for?

Brads are commonly used to attach shoe moldings and small ornamental parts on furniture. Brads are also useful when gluing delicate wooden parts together. It’s often helpful to apply glue to a joint and then drive a few brad nails into your project to hold everything while the glue dries.

Can you glue shiplap to ceiling?

Use an adhesive such as Loctite (liquid nails) to keep the boards from twisting or popping. Then finish with brad or 2” finishing nails. Use liquid nails to ensure a secure bond.