Table of Contents
How do you secure a fireplace mantel to the wall?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
How do you hang a heavy mantel on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
What holds up a fireplace mantel?
Since neither option is very sturdy, we recommend you attach the mantel to a cleat—a simple piece of lumber securely fastened to the wall. One cleat runs horizontally under the mantel shelf, and the others run vertically inside the legs (most mantels are hollow in back).
How are mantels attached?
As with many other forms of mantle or shelf, a fireplace mantel can be commonly attached to the wall with screws or lag bolts. Bolts are screwed into the wall above the fireplace before a mantel is slotted straight onto it. A rubber mallet can also be used to help ease the mantel out of position if it’s stuck.
How do you hang a mantel on a brick wall?
Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
How do you secure a floating mantel?
Make sure those marks are level, centered and extend far enough to cover the mantel’s length. drill holes at each mark. Drill Sleeve Holes. Drill holes at each mark using a drill and 3/4″ masonry bit. insert lead sleeves into holes. Insert Sleeves. drive lag bolts. Drive Lag Bolts. install the mantle. Install Mantel.
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
How do you attach a mantel to a stud?
Installing Support Rods The mantel needs to anchor to the studs in the wall above the fireplace. Drive 1/2- or 3/4-inch rebar rods or lag screws into pilot holes drilled into the studs. For best support, drive them all the way through the stud. Place one rod or screw in each stud behind the mantel.
How do you install a wood fireplace lintel?
How to Fit a Lintel in a Chimney – A DIYers Guide! Decide On Lintel Height. Remove a Brick Either Side Where The Lintel Will Be Installed. Cut Lintel To Size. Install the Lintel On a Bed of Mortar. Re-lay Any Remaining Bricks. Make Good Any Surrounding Work.
How is a mantle attached to a brick fireplace?
The mantel is lifted into its wall position by aligning the holes to the support rods. The mantel is pushed back into the rods and against the bricks. Secure attachment of a mantel to a brick fireplace is realized by tapping it in with a hammer and a scrap wood spacer.
What is the wall above a fireplace called?
The fireplace mantel or mantelpiece, also known as a chimneypiece, originated in medieval times as a hood that projected over a fire grate to catch the smoke. Mantelpiece is now the general term for the jambs, mantel shelf, and external accessories of a fireplace.
How much is a fireplace insert?
How much does a fireplace insert cost? Most fireplace inserts and a professional installation cost about $2,000 to $4,000, depending on the state of your existing chimney and the model you select. Some electric models cost significantly less, but they offer less heat output than wood and gas fireplace inserts.
How far should a mantle stick out?
A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).
How do you attach wood beams to drywall?
Covering the Beam Screw drywall to a wooden beam on the three exposed sides to cover them, using type W drywall screws, also called “coarse thread” screws. Add joint compound, commonly called “mud” in the drywall trade, at the inside and outside corners.
How heavy can a mantle be?
The maximum weight for all 60INCH MANTELS is 150 lbs. The maximum load for all 72 inch mantels is 180 lbs.
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
Why do fireplaces have mantles?
Why Do Fireplaces Have Mantels? The purpose of a fireplace mantel was traditionally to catch smoke before it entered the room from the firebox of an open fireplace, but mantels in more modern times are used primarily for decorative and aesthetic purposes.
How do you secure a wood mantel to brick?
Modern Timber Craft says to insert a lag bolt into each sleeve and tighten it with a screwdriver or drill until it is secure. Then, use an angle grinder to remove the head of each bolt. If a different set of hardware is provided with your mantel, anchor the hardware to the brick using screws in the inserted sleeves.
