Table of Contents
Can grab bars be installed over tile?
Grab bars can be installed on surfaces like drywall, tile, fiberglass, stone, concrete and wood paneling. For the most support, grab bars should be attached directly to the studs inside a wall.
How do you install a grab bar in a ceramic shower?
Does a stud finder work through tile?
Tile isn’t secured by metal fasteners, but its cement board substrate often is. Magnetic stud finders are highly effective at finding studs behind drywall but far less effective at finding anything under the many layers of tile and tile substrate. You may be able to detect a fastener if you are patient and slow.
Where is the best place to put grab bars in the shower?
Shower Stall Grab Bar Placement Here are a few rules of thumb for where to place grab bars in your shower. Vertical entrance bar should go close to the shower door jamb. Horizontal bar should go along the side wall, 34-36 inches above the floor. Vertical bar on the faucet end wall should go near the faucet handles.
Where should shower grab bars be installed?
Grab bars can be installed on the back wall and control wall of the shower stall. The ADA recommends that two bars be installed on the back wall, one 8 to 10 inches from the rim of the tub and the other parallel to it 33 to 36 inches from the base of the tub.
Do shower grab bars have to be installed in studs?
We’ve taken a look and pulled together the answers for you! Grab bars are highly recommended to be installed into wall studs to ensure the security of the bar. Adding grab bars on the walls, near the shower and toilet, will allow these individuals to regain some independence.
Can you use toggle bolts for grab bars?
Our solution, which we recommend, is to use toggle bolts to attach the grab bars. Toggle bolts have wings that open inside a hollow wall. They are commonly used to hang heavy objects on drywall where setting a screw or nail in a stud isn’t possible.
How do you find studs in bathroom tiles?
To find the location of wall studs behind a tile wall in a bathroom: Use a standard stud finder above the tile, and plumb down from it. Use a special deep sensor stud finder than can go through tile.
What type of drill bit is needed for ceramic tile?
Ceramic tile can be drilled with a carbide bit, while glass and porcelain call for a diamond-tipped bit. While that sounds expensive, a ¼ inch diamond tipped tip costs under $20, and a carbide bit of the same size can be had for less than $10. When in doubt, buy the diamond bit. It will drill any type of tile.
Can I use a magnet to find studs in wall?
If you slowly slide a magnet along the surface of your wall, it will be attracted to the steel drywall screws that come up very close to the surface of the drywall. A plastic coated magnet is attracted to the steel screw that’s just beneath the surface, making studs easy to locate.
What is deep scan on stud finder?
DeepScan® Mode doubles the scanning depth to locate the edges of wood and metal studs up to 1 1/2 in. ( 38 mm) WireWarning® Detection indicates the presence of live, unshielded AC electrical wiring up to 2 in. ( 50 mm) deep in both stud scanning modes.
What are the ADA requirements for grab bars?
Both types of bars have to be between 33 and 36 inches above the finished floor. Side wall grab bars should be at least 42 inches in length, with one end 12 inches or less away from the wall behind the toilet, and one end at least 54 inches away from that wall. Rear wall grab bars must be at least 36 inches long.
How many grab bars should be in a shower?
There should be a minimum of 3 grab bars in a standard shower stall. They should be position in the following spots: On the wall at the entrance to the shower stall. This is normally a small grab bar positioned vertically.
What is the standard height for a grab bar?
The ADA says that grab bars should be installed horizontally between 33 inches and 36 inches maximum above the finished floor to the top of the gripping surface (section 609.4). This is likely due to average height and common usage.
Why is there a grab bar behind toilet?
Grab bars next to a toilet help people using a wheelchair transfer to the toilet seat and back to the wheelchair. They also assist people who have difficulty sitting down, have balance problems while seated or need help rising from a seated position.
Is vertical grab bar required?
Grab bars are required in accessible toilet rooms. The ADA Standards require horizontal grab bars on the rear wall and side wall of the water closet, but it does not specify a vertical grab bar. However, you will often see them while in a toilet room or in the accessible stall.
How high is a shower niche?
Positioning your niche at chest to eye-level is a good standard. This translates to a height of about 48 to 60 inches. Ideally, you’ll want to position your niche to fit between the studs which are usually located 16 inches apart. But many contractors can help you with planning the space for a more custom look.
How do you attach a grab bar to drywall?
Attach the grab bar to the wall. With the mounting flanges placed over the marks you made, screw the included screws into the flanges, through the drywall and into the wooden studs. You will need to use some force when you start screwing into the wooden studs.
Can you drill a tile with a normal drill bit?
As mentioned earlier, drilling through tile requires a specialist drill bit – regular or even masonry bits simply won’t do the job as they’re not strong enough to penetrate tiles’ hard surfaces. Instead, you should opt for either carbide-tipped or diamond-tipped drill bits.
