Table of Contents
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
How is a mantle attached?
Since neither option is very sturdy, we recommend you attach the mantel to a cleat—a simple piece of lumber securely fastened to the wall. One cleat runs horizontally under the mantel shelf, and the others run vertically inside the legs (most mantels are hollow in back).
How do you hang a heavy mantel on drywall?
Holding your drill at a 45 degree angle downward, drill a pilot hole through the shelf and drywall and into the stud. Install a finishing nail into each of the pilot holes with a nail gun or hammer; the nails must be long enough to penetrate at least 1 inch into the drywall. These nails will secure the mantle in place.
How do you hang a heavy wood mantel?
Slide Over Bolts Method Locate the studs behind the brick, stone, or faux veneer. Drive 1/2in lag screws through each of the studs. Have a helper support the mantel while you mark the location of the support rods on the back of the beam. Apply construction adhesive into the holes. Slide into place, admire, and enjoy!.
How is a mantle attached to a brick fireplace?
The mantel is lifted into its wall position by aligning the holes to the support rods. The mantel is pushed back into the rods and against the bricks. Secure attachment of a mantel to a brick fireplace is realized by tapping it in with a hammer and a scrap wood spacer.
How do you install a floating mantel bracket?
Make sure those marks are level, centered and extend far enough to cover the mantel’s length. drill holes at each mark. Drill Sleeve Holes. insert lead sleeves into holes. Insert Sleeves. drive lag bolts. Drive Lag Bolts. Drill Mantel Holes. Mark on the rear of the mantel where the lag bolts will hit. install the mantle.
How heavy can a mantle be?
The maximum weight for all 60INCH MANTELS is 150 lbs. The maximum load for all 72 inch mantels is 180 lbs.
How do you attach a mantel to a stud?
Installing Support Rods The mantel needs to anchor to the studs in the wall above the fireplace. Drive 1/2- or 3/4-inch rebar rods or lag screws into pilot holes drilled into the studs. For best support, drive them all the way through the stud. Place one rod or screw in each stud behind the mantel.
What is a floating mantel?
Our mantels are hollow on the inside, providing an easy alternative to solid wood mantels. Live grain end caps maintain the look of a solid piece of wood. Each mantel is hand crafted from reclaimed longleaf pine, providing a unique look and character that cannot be duplicated.
How do you fill a gap between a wall and a fireplace?
You can fix gaps between brick fireplaces and sheetrock. Measure the size of the gap between the drywall and the brick. Use 1/4-round trim molding that’s wide enough to cover the space of the gap. Place a tube of acrylic caulk into a caulking gun. Replace the caulk in the caulk gun with a tube of construction adhesive.
How far should a mantle stick out?
A mantel should stick out at least 6 inches (15.24cm) from the wall. It’s the perfect depth that allows you to have a mantle effectively deflect heat without compromising aesthetics. You can extend it to have more depth for your decorative pieces, but we don’t recommend having it less than 6 inches (15.24cm).
How do you secure a mantel to a brick fireplace?
How to Install a Mantel Remove the old mantel. Add support by drilling holes for lag shields, then install lag bolts into the brick. Measure carefully and drill corresponding holes for the wood mantel. Push the wooden mantel carefully into place using wood glue for extra support.
How do you attach a wood mantel to a brick fireplace?
Lift the mantel and position it in place, aligning the holes in the back of the mantel with the support rods. Push the mantel onto the rods until the back of the mantle is against the bricks. Gently tap with a small hammer and a small piece of wood if necessary to completely align the mantel next to the brick.
Can you insert a wall mount fireplace?
Wall mount electric fireplaces aren’t designed to be built-in like electric fireplace inserts but some can be partially recessed or fully recessed into a wall. A wall mount electric fireplace is a type of electric fireplace that is designed to be installed on the surface of a wall.
How high should a wall mounted fireplace be?
How high should a wall mounted fire be? You can fit your fire anywhere on your wall so long as it meets any installation requirements. Many people like to have them at eye level from a seated position, which works out about 40-42” off the floor. Others like to place them between their wall mounted TV and the floor.
How do wall mounted fireplaces work?
A fireplace that’s designed to go into a wall or cabinet, will expel the heat out a vent in the front of the unit. A fireplace that’s designed for surface mounting will expel heat out the top or the bottom of the unit.
Can you screw in shiplap?
When using screws, you are more likely to split the material. This can lead to unsightly cracks and unusable material. You would also need to predrill the holes, which will add extra time and labor to the project. We don’t recommend using screws when installing shiplap to save yourself time, money and the headache.
Can you mount shelves on shiplap?
This mark was for the top of the bracket (see below). Then we put pilot holes into the wood and drywall, then drilled them into place with long screws into the studs. With these brackets you’ll just butt up to the shiplap directly. The shelf will still sit on top and you’ll screw it down when your brackets are set.
Where should mantel brackets be placed?
Mantels 2” Thick or more and 7-12” Deep- Brackets can be spaced up to 48” apart. That means, you would place a bracket 24” to the right and 24” to the left of the mantel’s center. It is ideal to bring the brackets in from the side at least 6-10” (depending on how long the mantel is).
What type of wood is used for mantels?
Walnut is a popular choice for fireplace mantels. It is a harder and heavier type of wood than most and is extremely durable. The rich dark brown wood is an excellent for an impressive fireplace mantel. Hickory is also a great choice for a fireplace mantel if you are going for a unique look.
