Table of Contents
You can attach a ledger board to a house for a patio cover by fastening it to the framing through the siding, or the rim joist. A rim joist is your best bet as it is quite secure but is only possible for two-story houses.
Can I attach a ledger board to a fascia?
If you own a two-story home, you can tie the ledger into a band joist. Find the band joist by measuring down from the 2nd story window. When you attach the ledger boards to the fascia, they should be held securely with bolts through the wall, or you can use lag screws.
Should I use ledger board spacers?
If you have your ledger tight against the rim joist it’s much stronger. If it’s flashed properly you won’t have to worry about spacers.” Flashing, of course, is key. Any water trapped behind the ledger can induce rot, if not in the ledger itself than in sheathing and framing of the house.
How do I attach a ledger board to a house with vinyl siding?
For the most secure attachment, ensure the ledger board fastens to the rim joist, just below the floor of the house. Locate the rim joist and mark an outline on the siding where you want to position the ledger board using a tape measure, pencil and chalk line. Cut away the marked area of siding with tin snips.
How do you attach a ledger board when you have no rim joist?
If you do that the ledger will also be tight to the concrete so you could use anchor bolts to the concrete. some times you can just go with the wider ledger to allow you to get low enough to use anchor bolts. Or you open the wall in the garage so you can put some solid blocking in there.
How do you cut stucco on a ledger board?
You will need a circular saw with a diamond blade and a cold chisel. Once you have drawn the outline of your ledger board on the stucco, you can cut through the stucco and the metal screed it uses to grip to the house. Be careful not to cut too deep and concentrate on cutting a straight clean line.
How do you secure wood to stucco?
Align the wood’s hole with the hole in the stucco. Mount a lag screw’s head into the nut driver. Press the screw tip through the wood and through the hole in the stucco until the tip rests against the stud. Drive the screw into the stud until the screw’s head pulls the wood flush against the stucco surface.
Can I attach a ledger board to wall studs?
Mike Guertin (on Instagram @mike_guertin), a builder and remodeler in East Greenwich, R.I., and a presenter at JLC Live, responds: Yes, it’s technically possible to fasten a deck ledger to the narrow faces of 2-by studs rather than to a solid rim joist.
How do you attach a pergola to a patio?
If you want your pergola positioned over a patio or concrete – choose the second option as the Fixing Post is secured by using a hammer drill and masonry bit to drill through the hard surface and then secured using the special masonry bolts provided.
How much weight can a ledger board hold?
The ledger is 10′ long so every foot of ledger must be designed to carry at least 200 lbs of load.
Can you attach a patio cover to fascia?
Patio Covers directly attach to your homes fascia board with the included hanger, your fascia board needs to be a minimum of two inches thick and allow enough space for the hanger to attach.
How do you attach fascia to roof trusses?
Instructions for How to Attach Fascia Board to Roof Trusses Mark the place closest to the end of the board that aligns with the center of a joist. Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place.
What is behind ledger board?
Ledger boards are made from lumber of the same dimensions as the rest of the rim joists on your deck. Depending on the height and size of your deck, the rim joist may be made of 2-by-6 or larger planks. Treated lumber is typically the material of choice, since the deck ledger is exposed to the elements.
What is ledger board attached?
Attaching a deck ledger board. The ledger board must be fastened to the adjoining building’s lumber frame. The most common part of the building’s frame that a ledger is attached to is the rim joist (also called the “band joist,” “band board” or “rim board”).
How many lag bolts for a ledger board?
Since 2009, every edition of the IRC (including the anticipated 2021 edition) requires the deck ledger to be connected to the house floor band joist with ½” bolts or lag screws as shown in Table 507.9.
How do I find the wheel joists in my house?
You just need to measure from the window at the ledge, to the floor. Add 3/4″, and there you go. If there is already a deck on that level. It will be attached to the Ledger Board, that should be bolted to the Header or Stringer, that the floor joists are attached to.
How do you find studs on a ledger board?
Use a good quality stud finder or rap firmly on the wall and listen for a solid sound, indicating a stud is beneath. You can also check base molding or crown molding for filled nail holes, which indicate stud location. Another clue is the location of outlets and switch boxes because one side should connect to a stud.
What kind of anchor do you use for stucco?
Tapcon Anchors: Tapcons are also a great choice of screws for stucco walls and they are noticeably blue in color which can be a downside for some people if exposed, as you can see in the image.
What kind of screws go into stucco?
What Kind of Screws Should I Use for Stucco? You can use stucco screws or concrete screws. That’s because stucco is a hard material like concrete. You will notice that these screws have special features like a diamond tip for enhanced penetration into hard stucco and concrete.
What is a screw anchor?
Screw anchors are inserts, typically made from plastic, metal, or fiber, which enable the attachment of screws into brittle materials — such as masonry or dry wall.
How do you attach a ledger board to a wall?
Use a wood bit to drill ½” pilot holes through the ledger board. Next, use a concrete bit to drill into the concrete wall. Install two bolts at the end of each ledger board. Hammer the sleeve anchor through the ledger board into the concrete wall.
How long should ledger screws be?
Your bolts or screws should be long enough to extend at least ½” past the board you are attaching to. They are usually installed in a zig-zag pattern.
How thick should a ledger board be?
The decking is 1-inch thick, so the top of the ledger is 1 1/8 inch below the bottom of the sill.
