Table of Contents
How much overhang should a face frame have?
Face frames on sides of kitchen cabinets should overlap 1/4 in. on the outside edge. This makes room for adjustments when installing them next to one another.
What is a face frame screw used for?
Installing cabinets and framing structures require specific fasteners to get the job done right. You need fasteners that will install easily to wood and without breaking, and you need fasteners that deliver the holding power needed to ensure the integrity of your project. In short, you need face frame screws.
What are pony clamps used for?
Pony Hold-down clamp Designed to rotate a full 360 degrees around the holding bolt, the Pony hold‑down clamp can be used on any wood or metal surface. This heavy‑duty woodworking clamp also has a unique square‑head screw that can be tightened or loosened with a wrench.
How much reveal on face frame cabinets?
We want the doors and drawer fronts to cover as much of the face frame as possible for a nice clean look, but we have to be careful to not have the doors overlapping or rubbing on the ones next to it. We need to leave a 1/4″ reveal (gap between doors and drawer fronts) to ensure that they open and close properly.
What screws to use for installing kitchen cabinets?
Use a #8 x 1-5/8″ screw to secure cabinets together. After you install all of your cabinets, it may be necessary to adjust the drawer fronts so they are level and have the proper reveals.
What size screws do I need to hang kitchen cabinets?
Attach the cabinets to the wall using No. 8 or No. 10 screws, approximately 3½ inches long. The best make of this screw that I’ve seen is the one by GRK.
What screws to use to hang shelves?
Drive a 2 ½-inch long flathead screw 1/8 inch in diameter through the top hole in the shelving standard and into the stud. Place a 4-foot-long carpenter’s spirit level against the standard.
How do you fix a cabinet door that fell off?
How do you fix a broken hinge? Remove the loose screws. Coat a wooden golf tee with glue. Tap the tee into the hinge screw hole with a hammer. Score the tee with a utility knife flush with the mortise. Break the tee off even with the bottom of the mortise. Allow the glue to dry.
Can a cabinet stile be removed?
Drill entirely through the center stile, then close the door and from the inside of the cabinet make pilot holes into the door ( Caution: do not drill through the door, a small pilot start is all that is needed). Cut the top of the center stile with the cabinet saw or jam saw.
Can you remove center stile in upper cabinets?
If your cabinets close on the stile and don’t meet in the center and the stile shows, it can be carefully removed and then added to one of the cabinet doors so that when they’re closed, the stile still appears to be there.
What is a stile on a cabinet?
Stile – The vertical-framing members of a cabinet face frame or cabinet door.
What type of fasteners are used for carcass fixing to wood frames?
Screws. Woodscrews are used for joining wood, fastening ironwork to wood, fastening hardware (hinges, locks, catches) to wood. A screw is a metal fastener with a spiral thread cut in.
Can you use plywood for face frame?
Trim the edges of the veneer to the edges of the plywood and rip the plywood into the various widths for your face frame. Cut the rippings to length for your face frame. Now peel off the veneer pieces and put your face frames together with the plywood pieces using whatever method you choose.
What is a face frame drawer?
Face frame is a reference to a framed cabinet’s trim boards that are visible on its face. The face of a cabinet is the visible end where the drawers and doors are accessed. The face frame will typically be made from different material than the cabinet’s less noticeable back and side panels.
What are clamps used for in film?
They can be used for mounting gels to a light — just be sure the clamps have rubber so you don’t ruin the gels. You can also use them to mount reflectors, sound blankets, or material for a cyc wall. Professional grips usually have quite a few of these available at all times.
What is the function of clamp?
Clamps are versatile tools that serve to temporarily hold work securely in place. They are used for many applications including carpentry, woodworking, furniture making, welding, construction and metal working.
How much reveal on full overlay cabinets?
A Full Overlay door will overlay that same 1.5” face frame 1.25”, leaving a ¼” reveal on the sides (stiles) and bottom (rail).
What is overlay on face frame cabinets?
A face-frame cabinet is a cabinet which has a front panel into which an opening has been cut. The overlay dimension is simply how much bigger the door is than the opening of the cabinet (as measured on the hinged side of the door).
What is the reveal on a cabinet door?
Door reveal refers to the portion of a cabinet frame left exposed after the door is attached. The size of your reveal is determined by the size of your doors in relation to your cabinet case frame.
How wide are stiles and rails on Shaker cabinets?
There is no given rule for width or length on stiles, but there are industry standards that are relied on for balance and efficiency. Typical width for shaker stiles on panels, doors and drawer fronts usually is 2 1/4 inches. This is the same width used on standard door and window casing, as well as ordinary baseboard.
How is cabinet width measured?
Lay the tape measure along the bottom of the cabinet; place the end against the back of the cabinet, then pull out the tape until the front edge of the cabinet to find the front-to-back (depth) measurement. Next, measure the total outer width of your cabinet.
