Table of Contents
How do I attach a deck ledger to vinyl siding?
Attaching a Ledger Board to Your House Remove Siding. Determine the outside dimensions of the framing for the deck and add ½” to 1″ to that length. Important. Set the Height of the Ledger Board. Block Joists from Inside the House. Install First Flashing Piece. Bolt Ledger in Place. Install Second Flashing. Attach Joist Hangers.
Can you attach a deck to vinyl siding?
Attaching a deck ledger board to a vinyl-sided house requires a few extra trim pieces to keep water from leaking behind the siding. Here’s a rundown of the materials and procedure.
Can you put a ledger board over siding?
In order to install the ledger board, you usually need to remove the house’s siding. Never install a ledger board over the top of siding no matter what you hear, this can weaken the connection. Set the blade depth so you won’t cut into the house sheathing below the siding.
How do you attach wood to vinyl siding?
Follow these easy steps to install siding hooks on vinyl siding: Locate the horizontal seam where the siding pieces snap together. Lift the upper siding piece lightly and slowly insert the hook between the seam, with the hooked side facing out. Push the hook firmly until it snaps into the seam.
Should decking go under siding?
Keep in mind the bottom of the upper siding should be at least two inches above the flashing or the decking that’s near the house. Never put horizontal siding in direct contact with any horizontal material.
How far should deck boards be from siding?
Either use two stainless steel screws through the face of the board at each joist or ExoDek QuickClips to fasten the boards to the deck frame. The first board you install should be about 1/8″ (3.5mm) away from the siding, to account for drainage, expansion and contraction.
Can I screw into vinyl siding?
Vinyl coated screws are great too. No matter which screw you buy, make sure it is a Phillips head screw because they are the easiest to use. Obviously, you want to be safe when climbing ladders to drill into the siding. Make sure that your ladder is secure and that the cord for your drill is clear of your work area.
Is deck flashing necessary?
More often than not, a major contributor is worn or missing flashing. Without flashing, there’s nothing to prevent water from seeping behind the ledger board that connects deck framing to the house. It’s a thin layer of waterproof material that keeps water from getting into places it doesn’t belong.
How many lag bolts for a ledger board?
Since 2009, every edition of the IRC (including the anticipated 2021 edition) requires the deck ledger to be connected to the house floor band joist with ½” bolts or lag screws as shown in Table 507.9.
How do you find studs in vinyl siding?
Start at the top of the wall where you know there is a stud. Tap the end of the tape measure (or hammer) lightly on your siding. Tap it at each end of the wall, and at every 16 in. or so, until you hear a hollow echo in one spot. That means you’re in between the studs.
Does siding need to be nailed into studs?
Siding must be secured into metal studs if the substrate is not a nailable surface such as exterior dry wall, gypsum board, etc.
Can I use screws for wood siding?
Although ring-shank siding nails are suitable for wood siding installation, screws have better holding power over time. Stainless steel is strongly recommended for all woods and required for modified woods such as Accoya and Kebony.
Can you attach a floating deck to the house?
Attaching a floating, moving deck to a solid house will cause either the deck to break off or damage the foundation of the house with the added stress of the rising and falling of the deck. For both the good of the house and the deck, never attach a floating deck to a house.
Do you have to stagger deck boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Should deck boards have a gap?
When using wood decking, you want a gap of at least 1/8 of an inch after your decking has dried out. If you’re using decking that’s already been dried out, you can leave a 1/8-inch gap when you install. Many decks will use “green” wood, or wood that hasn’t been dried down or kiln dried.
How far apart are joists for a deck?
Step 4: Make Sure Your Joists Are Spaced Correctly Deck joist spacing should never exceed 16″ on center (with the exception of MAX deck boards, which allow for maximum 24″ on center). For a more rigid feel, 12″ or less may be preferred.
How do you support a free standing deck?
Buried support posts can help brace the deck and resist uplift from strong winds that could tip a freestanding deck over. However, buried posts are susceptible to wood-destroying insects. Structural hardware can connect deck posts above the ground to the concrete footings.
