Table of Contents
How do you make a bookshelf step by step?
How to Build a Bookshelf in 8 Steps Step 1: Cut the Legs, Shelves, and Supports. Photo by Kolin Smith. Step 2: Attach the Supports to the Legs. Step 3: Assemble the Box. Step 4: Level the Bookcase. Step 5: Plumb the Bookshelf. Step 6: Attach the Kick Board. Step 7: Scribe the Trim to Fit. Step 8: Apply Nosing to Shelf Faces.
How long does it take to put together a bookshelf?
Even though this project isn’t complicated, it’s still going to take you at least 40 hours to build. A bookcase or shelf is an extremely useful home storage system.
What tools do you need to put together a bookshelf?
As for basic tools, you’ll need a portable circular saw, hammer, block plane, combination square, tape measure, metal rule, two clamps, nail set and putty knife. Other supplies include glue, nails, sandpaper, wood filler and varnish or paint and shellac.
Can one person assemble a Billy bookcase?
They are even easy to assemble alone, although I think the directions recommend two folks. I had no problem putting them together by myself. I assembled the first Billy shelf in the office. That worked great until it was time to slide the back into the bookshelf.
How hard is it to assemble a Billy bookcase?
With only 12 steps (13 if you’re mounting it to your wall), it’s much less intimidating and much more intuitive than other IKEA items. It took me about 1 hour to build, and when I was done, I had something that looked a lot more expensive than $50. If I built this and didn’t hate everything, than you surely can to!Nov 7, 2018.
How many shelves does the Billy bookcase come with?
ceiling height required: 80¾”.1 stationary shelf and 4 adjustable shelves included.May be used with BILLY corner hardware to form a stable corner unit.Can be used with BILLY height extension unit in the same width for added storage vertically.May be used with doors; available in different colors and designs.
How do you make a book shelf stable?
Right the bookshelf and put it back into position. Raise or lower each foot until the bookcase stops wobbling. Raise the feet by turning them clockwise; lower them by turning them counterclockwise. Affix the bookcase to the wall for maximum stability, advises Today’s Homeowner.
What is the backing of a bookshelf called?
I’ve used 1/8″ luan to back a bookshelf before and it did well. It’s also known as “door skins”.
Do shelves need to go into studs?
As a general rule, it’s always ideal to install shelf brackets into wall studs. However, it can be difficult to install brackets directly on a wall stud In that case, we recommend using a toggle anchor (which are available for purchase here).
How do you stack bookshelves?
Stack them horizontally, or shelve most vertically and then stick some horizontally on top of their new vertical buddies. Use your shelves for support. If you’ve run out of space on the bookshelves themselves, stack books next to them, using the bookcases as support.
Do you have to attach Billy bookcase to wall?
The Billy Bookcase is not specifically designed to be wall-mounted. Consequently, the only standard wall connection with the Billy Bookcase is two small brackets that attach the top of the shelving unit to the wall. That being said, there is no reason why you can’t get creative and wall-mount a Billy Bookcase.
How do you hang an Ikea bookcase on the wall?
Remove all of the items stored on the top shelf and the shelf directly below the top shelf. Place a right-angle bracket on each end of the top shelf so the bracket rests on the top of the shelf and against the wall. Drill a hole though each mark on the wall. Drive the anchor into the wall with a hammer.
How do you organize Cubbies?
These DIY Classroom Cubbies Will Make Your Classroom Organization Shine Build a bucket wall. Corral some crates into classroom cubbies. Turn trash bans into stash bins. Hang up sturdy plastic totes. Fasten plastic baskets to the wall. See why teachers love Trofast. Assemble a bucket tower.
How wide should shelf be?
The lowest shelf should be 3 to 4 inches from the floor level. Shelf width or span is determined both by aesthetics and sag considerations. Shelf depth for a general purpose bookshelf is usually 10 to 12 inches. Shelf spacing will generally range from 7 to 15 inches with 8 to 12 inches being common for bookshelves.
How tall do you have to be to reach the top shelf?
The recommended shelf height is between 87 and 96 inches from the floor. The shelf should also sit at least a foot away from the closet ceiling. Keep the top shelf height below 96 inches, however, as shelves of this height are not only very difficult to reach but impractical.
Can you assemble Billy bookcase without back?
The downside of not using backing is it makes the bookcases much less stable, but we are adding plenty of trim and wood facing so these are still solid as a rock. I wouldn’t recommend using an IKEA billy bookcase without the back unless you are planning to reinforce the bookcase somehow.
Can you take apart a Billy bookcase?
Are you soon to be moving house or have an old Billy bookcase that you’re ready to replace? The new IKEA disassembly instructions will make taking it apart quick and easy. This will mean that you pack up your IKEA pieces with ease ready to transport or donate.
How thick should bookshelves be?
Use 3/4-inch thick materials for shelves and bookcase structure. If you’re using hardwood solids, it’s OK to boost the thickness to 1 1/4 inch for almost unlimited support. This type of shelf looks more like a mantel and is expensive, but adds the opulent look of craftsmanship.
