QA

Question: How To Apply Bona Traffic Hd

Do you need to sand between coats of Bona Traffic HD?

INTERCOAT ABRASION: It is not necessary to abrade between Bona waterborne sealer and finish coats unless more than 48 hours has passed since the previous coat was applied. For smoothest results, abrade between all coats as necessary.

How many coats bona traffic?

How many coats of Bona Traffic HD should you use? Like Mega One, Bona always recommends a minimum of 2 coats of finish. Adding a third coat gives an extra layer of protection that may be right for some homeowners who are worried about scratches.

How long will Bona Traffic HD last?

You should wait three hours between coats. You can walk sparingly on the floor after 8 hours and Bona Traffic cure time for full usage is 24 hours.

Can you apply Bona with a roller?

Flooring is ready for TOPCOAT application (MEGA). 2. For field application – pour the BONA topcoat directly on to the flooring, you will see BONA will automatically spread out (self leveling property) Use roller to evenly distribute the coating, pour the coating along the grains termination should be from wall to wall.

How do you mix Bona Traffic HD with hardener?

Bona Traffic HD® Hardener Shake Bona Traffic HD finish (Part A) well for 30 seconds. Add Bona Traffic HD Hardener (Part B) to finish (Part A). One 10.38 oz. bottle of hardener will activate one gallon of finish. Immediately shake mixture vigorously for 30-45 seconds. Insert supplied filter into bottle.

Can you use bona traffic without hardener?

Absolutely! Bona Traffic does not become a urethane without the hardener. The finish will still dry but the film will be soft and will never reach its maximum durability.

How do you apply finish to hardwood floors?

Put your applicator on the floor, and cut into the finish. Then, use it to brush the finish up and down the floor, covering a couple of feet of the room. Apply a moderate, consistent amount of pressure when you push the finish, but don’t push down on the applicator while pulling it towards you.

Do I need Bona primer?

Bona Natural Primer can be used for a range of interior projects where preserving the natural, raw or untreated look of the wood is desired.Overview. Product Use Bona Intense Primer A 100% polyurethane based primer for finishes requiring better adhesion.

Is Bona Traffic a polyurethane?

Bona Traffic is a 100% polyurethane two component water-based top coat for the treatment of timber floors subjected to very heavy wear.

Does Bona have yellow traffic?

Bona Traffic remains clear for the life of the floor meaning it will not amber or turn yellow with time. There is also Bona Traffic Anti Slip which only comes in satin sheen.

How long does Bona cleaner take to dry?

Polish can be walked on with SOCKS on your feet after 1-2 hours. Allow 24 hours before resuming normal traffic, returning furniture and rugs, and allowing pets back to the floor. If desired, wait a full 24 hours before applying a second coat. Bona offers floor polishes and tools for hardwood, stone, tile and laminate.

Does Bona Mega one yellow?

During the sanding process, the finish offers solid abrasion properties while the high build of Bona Mega ONE creates a clear finish surface that will not yellow over time. Additionally, Bona Mega ONE is a low-VOC product that is GREENGUARD certified for indoor air quality.

Do you need to sand between coats of water based polyurethane?

Sanding between coats is not required for adhesion as long as the time between coats is less than 6 hours. However, screening or sanding between coats usually produces a smoother better looking finish. A minimum of 3 coats of finish are recommended. Sand between coats with 120-150 grit sandpaper or maroon abrasive pad.

Is Bona worth the money?

Bona Traffic HD costs a little more than the basic Bona Traffic. But, the difference in price is fairly insignificant. (Bona Traffic does cost significantly more than other water borne polyurethanes and it is WORTH it because it’s head and shoulders above the rest.

Which finish is best on hardwood floor?

What is the Best Finish for Hardwood Floors? Polyurethane is the most popular finish for floors. It’s tough enough to handle constant traffic and is resistant to almost everything. There are two types of polyurethane finish: oil-based (solvent borne) and water-based (waterborne).

How long should you wait between coats of poly?

If you use water-based polyurethane, you only have to wait between 2 to 4 hours before applying the next coat. However, when using oil-based polyurethane, you might wait for 10 to 24 hours. You can apply the next coat in as little as 4 hours if you are using fast-drying, oil-based polyurethane.

What NAP is a Bona roller?

European nap roller cover for waterborne finishes. The Bona Roller Cover a European nap roller cover meant for waterborne finishes. The candy stripe helps spot a dragging roller.

How do you use bona white?

Apply Bona White using a microfibre roller (we recommend Bona Roller) at approx. 12 m²/lit (83 g/m²), avoiding accumulation of product. When dry (approx. 2–3 hours), abrade to reduce grain raise using the Bona Scrad system or a sanding screen grit 150 or finer.