Table of Contents
How many coats should Behr deck over?
Detailed Application Tips. One 3.78 L of ADVANCED DECKOVER Coating can cover up to 7 m2 with 2 Coats. It is strongly recommended to fill cracks, nail holes and accessible board ends prior to applying the first coat.
How long does Behr DeckOver last?
If the DECKOVER coating is applied according to label directions to a properly prepared, sound wood or concrete substrate, the film can be expected to last as long as a high quality Solid Color Wood Stain. BEHR Solid Color Wood Stains last 5 to 10 years on horizontal surfaces and 15 to 25 years on vertical surfaces.
How long does it take Behr deck over to dry?
Dries to touch in 4 hours. Wait 24-48 hours before light foot traffic. 72 hours to full cure. Additional dry time may be needed in cooler temperatures and higher humidity.
How do you remove peeling from Behr Deckover?
The only good part about the peeling DeckOver was, it ended up being relatively easy to remove. Much of it came up just with our fingers- we could literally just pick it up and peel it off. What we couldn’t peel off with our hands, we used a scraping tool and would pry an edge off, then peel it off.
How much Deckover do I need?
One gallon of ADVANCED DECKOVER Coating can cover up to 75 Sq. Ft. with 2 Coats. It is strongly recommended to fill cracks, nail holes and accessible board ends prior to applying the first coat.
How long does Deckover need to dry before rain?
Yes, 36 hours is sufficient dry time before rain.
Will Behr DeckOver peel?
Bring new life to old wood and concrete surfaces with BEHR ADVANCED DECKOVER. This 100% acrylic formula conceals cracks and splinters up to 1/4″, and creates a smooth, slip-resistant finish that also resists cracking and peeling.
Why is my deck over peeling?
Because wood absorbs moisture from rain and snow, and when the sun comes out and dries the wood out, the moisture vapor from the wood needs to be able to pass through the stain and escape. If there is too much stain, it restricts the moisture from evaporating away, so peeling can occur.
Can you use Deckover on pressure treated wood?
Hi Louise, DECKOVER can definitely be used on newly pressure treated wood, as long as all label instructions are followed. We do not recommend pressure washing, but definitely clean the new pressure treated wood before applying DECKOVER.
What happens if you paint your deck and it rains?
If it rains within 48 hours of applying a treatment, the water will soak into the wood, and try and displace the stain. This can cause a blotchy, flaky look, rather than a smooth, even, coat. If it rains immediately after you’ve stained the wood, the stain will peel and flake off.
What is better than Behr Deckover?
Deck Resurface Stains like Behr Deckover, Olympic Rescue-It, Rust-Oleum Restore – Do They Work? They claim it is the smart alternative to deck replacement. It can be applied to wood surfaces such as decks, stairs, docks, composite decking, and more.
Can you put deck correct over paint?
Cabot DeckCorrect needs to be applied in two coats, and it has a relatively thick consistency. A double layer of thick stain isn’t the ideal surface to apply paint over. You can use Cabot’s Problem Solver Wood Stripper or Problem Solver Wood Cleaner to prep the area before applying your primer and paint.
How long before you can walk on Behr Deckover?
Wait 24-48 hours before light foot traffic. 72 hours to full cure. Additional dry time may be needed in cooler temperatures and higher humidity.
How long after rain Can I paint my deck?
Wet wood can impact the look of your newly stained deck. According to stain manufacturer Behr Corporation, you should avoid staining a deck for at least 24 to 48 hours after the deck gets wet. Otherwise, moisture in the wood will prevent the stain from adhering correctly to the deck.
What happens if it rains on a freshly stained deck?
If it rains within 48 hours after you apply the stain, the water will soak into the wood pores and try to displace the stain. This will result in a splotchy surface rather than an even tone. If it rains right after you apply the stain, the stain will peel and flake off.
How do you use advanced deck over?
How to Apply Advanced DeckOver® Coating Replace any rotting or unstable boards. Fill nail holes and cracks up to 1/4″, completely fill in with Advanced DeckOver ® coating using nylon/polyester brush prior to coating. Apply painters’ tape to any deck surface you do not want coated in the DeckOver product.
What kind of roller do you use to paint a deck?
What’s the right roller for the job? For staining a deck, go with a standard 9 inch napped paint roller. A napped roller will apply the stain in much the same way as a lambswool pad, but in a much more efficient way.
Can you paint over a peeling deck?
The best way to deal with a peeling painted surface would be to completely remove the paint and stain the deck. In the example you have cited, we will need to remove the paint from the damaged portion of your deck, sand the surface and then repaint. Use a chemical stripper solution mixed in a garden sprayer to start.
