Table of Contents
2 Cycle engine: The adjustment screw is on the side of the carburetor and is parallel to the ground. You can identify it by the lock nut at the base of the screw. Loosen this and turn the screw all the way into a soft seat, then back it out one and a half (1-1/2) turns.
Why does my ezgo backfire?
The Throttle May Not Be Closing Properly. A gas-powered golf cart utilizes a handful of different parts that help to keep the fuel flow smooth. When the fuel flow isn’t properly handled, there is a strong chance of a backfire affecting your cart.
Why does my golf cart only run with the choke on?
4 Answers. Dwight Coleman there are usually only a few possibilities if it only runs with the choke. One cause could be an air leak on the carb, head gasket, crankshaft seal. The other could be a clogged low speed and idle circuit.
How do I know if my golf cart solenoid is bad?
If your golf cart fails to turn on when you turn the key on, this is the most obvious sign of solenoid failure. The solenoid clicks a little with the ignition system in regular operation; in most cases, a failing solenoid will not snap.
What does an igniter do on a golf cart?
The ignitor boosts the signal and sends it to the ignition coil. The coil then creates the large spark that goes to the spark plug and fires the gas mixture in the cylinder. Ignitors can be the cause of a weak spark or they may fail completely and then the coil cannot create any spark at all.
How do I speed up my EZ Go gas golf cart?
One way to increase the speed of EZ Go golf carts is to incorporate an octane booster when you fill the tank. The cart will have more pick-up, and it could gain as much as 5 mph. A different approach is to take out the throttle linkage governor on the carburetor.
How do you adjust the governor on a EZ Go TXT gas golf cart?
How to Adjust the Governor on a Gas E-Z-Go Golf Cart Locate the governor arm mounted on top of the rear axle case underneath the cart. Loosen the adjusting locknut on the end of the governor spring. Retighten the adjusting locknut.
How do you adjust the governor on a EZ Go golf cart?
Tighten the governor spring located in the engine of most golf carts to adjust your cart’s top speed. 90% of EZ Go Carts have simple springs which limit the speed of the engine. To raise the top speed of your golf cart, all you need to do is locate this spring and tighten it slightly.
How do you adjust the carburetor on a Yamaha golf cart?
Find the pilot adjustment screw on the edge of your carburetor. Pay attention to this screw – it should be a sharp point and not flat. Carefully remove this screw and then carefully screw it back. Turn this screw out one and one-half turns to adjust it properly.
How does a club car fuel pump work?
The fuel pump has several nozzles on it to accept the vacuum line, and both the Fuel In and Fuel Out lines. Inside the pump, there are several diaphragms which use the pulsing action created by the vacuum of the crankcase pressure to draw fuel from the storage tank and push it onward to the carburetor of the golf cart.
How do I make my EZ Go golf cart idle?
Push the throttle cable toward the throttle valve body on the engine from the gas pedal position. Screw the throttle cable back in place on both the gas pedal and the throttle valve body on the engine. The golf cart will idle rather than shut off.
Does a gas golf cart idle?
Gasoline golf carts do not idle because they need to be quiet / no exhaust during the period when a golfer hits the ball. A golfer drives up to a position near his golf ball puts on the brake, cart stops, engine stops, everything is quiet.
Why does my gas golf cart backfire?
In almost all cases, whether it is a 2 cycle or 4 cycle engine, golf cart backfiring is caused by the accelerator cable being out of adjustment at the throttle plate of the carburetor. With the ignition key in the OFF position and the seat completely removed, press the accelerator pedal down.
Where is the reset button on EZ Go golf cart?
Look in the area where several electrical wires enter the motor and locate a small red button. This is the reset button.
How do I troubleshoot my EZ Go golf cart?
Things to Keep in Mind Before Troubleshooting EZGO golf cart batteries aren’t perfect right away. Sticky accelerators are perfectly normal and can be fixed easily. Keep your cart stable. Make sure your charging wall socket isn’t faulty. Keep your tire pressure stable. Troubleshooting the speed controller.
How do you test a ezgo gas solenoid?
Set your voltmeter to the ohms reading, and connect its probe to each one of the big terminals. Of course, the reading should be zero. Next, move the cart’s switch to forward, turn it on, and accelerate slowly. Your solenoid should click.
