Table of Contents
What temperature should a gas hot water tank be set at?
120 degrees Fahrenheit is the safety recommendation against scalding, but 140° is the common default setting. Most experts agree that anything below 120 degrees creates a risk for bacteria to develop inside your water heater from stagnant water, such as legionella that causes Legionnaire’s disease.
Where is the thermostat on a gas water heater?
On most gas water heaters, the gas control valve, which includes both a thermostat and a heat limiting device, are located on the outside of the unit, near the bottom. It can be identified as the component with the controls for temperature and the pilot light.
What should water heater be set at AB or C?
The Department of Energy recommends setting your heater to 120 degrees Fahrenheit. That should be plenty hot enough for most uses in your home. Now, some water heater temperature controls come with settings that read “A-B-C” as opposed to numbers.
Is 50 degrees hot enough for hot water?
So, what is the best temperature range for your water heater? The EPA recommends 120 degrees because it’s hot enough to keep diseases at bay, it’s not hot enough to cause scalding, it will supply enough hot water for most small families and is relatively energy-efficient.
What is the best setting for a water heater?
The Consumer Product Safety Commission (CPSC) recommends setting the water heater at no more than 120 degrees Fahrenheit (49 degrees Celsius) to prevent scalding. Not to mention, a water heater that is set too high can unnecessarily increase your electricity bill. Of course, every house is different.
How do I adjust the temperature on my AO Smith gas water heater?
The thermostat’s control is a small screw set into a covered housing, and you’ll need a flathead screwdriver to turn it. Temperature adjustment is simple and intuitive; you’ll turn clockwise to increase the temperature and counterclockwise to lower the temperature.
How do you adjust the temperature on a Rheem gas water heater?
Pull the insulation from the cavity behind the covers to expose the thermostats. Insert a small flat-head screwdriver into the slot on the thermostat dial. Rotate the thermostat to your desired temperature. Make sure to adjust both thermostats if your Rheem water heater has two access covers.
How do I know if my water heater thermostat is bad?
If you turn the hot water tap and cold water runs out, then the upper thermostat is damaged. But if the water is hot that becomes later becomes cold, then you have a damaged lower thermostat.
How do you check a thermostat on a gas water heater?
How to Test a Water Heater Thermostat Switch the water heater’s power off. Remove the access panels and insulation so you can access the thermostats/elements. Using a screwdriver, set the upper thermostat on high, and the lower thermostat on low, by turning the dial in the middle. Turn the power back on.
Can you change the thermostat on a gas water heater?
The water heater thermostat is part of the gas valve. They cannot be replaced separately from the valve.
Is 140 too hot for water heater?
Professionals recommend keeping your water heater set at a temperature between 130 and 140 degrees Fahrenheit. Any higher, or lower, could actually be dangerous for you and your family. While turning the temperature up higher can result in burns, turning it lower than the recommended setting can also be dangerous.
What is pilot setting on gas water heater?
On gas water heaters, the pilot light makes sure that there’s always flame available when the burner needs to kick in and heat water. If you run out of gas, install a new water heater or have to shut it down for some reason, lighting the pilot is the first step to turn on a water heater.
Is 60 degrees too hot for water?
In general, hot water is 130 F (54.4 C) or above. Warm water is between 110 and 90 F (43.3 to 32.2 C). Cold water is generally between 80 and 60 F (26.7 to 15 C).
Is 150 degrees too hot for water heater?
The recommended setting for household water heaters is not 150 degrees, but slightly less _ 140 degrees. Water temperatures higher than 140 degrees can burn the skin and are particularly dangerous for young children and the elderly.
What is normal temperature for domestic hot water?
The ideal temperature for domestic hot water is 120 degrees Fahrenheit, or 49 degrees Celsius, to avoid the possibility of scalding. Furthermore, if the water heater is set at too high a temperature, it can result in unnecessarily more expensive energy bills from the running water emerging from shower systems and taps.
Should the top and bottom water heater thermostats be set to the same temperature?
The majority of electric water heaters have two thermostats: an upper and a lower, located under two control panels. To ensure your electric water heater works as efficiently as possible, you should set both of the thermostats at the same temperature.
How do you adjust the temperature on a Dux gas water heater?
When the pilot flame remains alight with the control knob released, turn the control knob anticlockwise to one of the number settings. A minimum setting of “6” is recommended and this will give a water temperature of about 60°C. Turn the control knob to a higher number for higher water temperatures.
