Table of Contents
Follow the pilot tube to the control handle until you see an air chamber, and there is where you’ll find the screw. Turn the screw clockwise in small increments to reduce the size of the pilot flame. To increase the flame size, turn it counterclockwise.
Can a pilot light flame be adjusted?
On some fireplaces, there will be a “Lo-Hi” button that allows you to adjust the flame upward or downward. On others, there will be a screw that you can easily adjust with a screwdriver. Turning the screw clockwise will lower the flame, while a counterclockwise motion will turn it up.
Why is my pilot light flame too high?
So, if your pilot light flame also tends to be too high, ensure that your fireplace doesn’t have a button to bring the flame up or downward. If there’s no such button, adjust a screw on the fireplace. Turning it clockwise will reduce the fire whilst moving the opposite direction will raise it.
What causes a weak pilot light?
Some of the reasons your pilot light keeps going out include: A poor pilot flame – low gas pressure or blocked orifice. A flame that is set too small. An insufficient supply of gas.
How do I adjust my oven pilot light?
Follow the pilot tube to the control handle until you see an air chamber, and there is where you’ll find the screw. Turn the screw clockwise in small increments to reduce the size of the pilot flame. To increase the flame size, turn it counterclockwise.
Is my pilot light too high?
Next to the “Pilot” indicator on the furnace’s control switch, there is a small screw located near the pilot light-thermocouple assembly. If it extends well above the thermocouple, it’s too strong. If the flame covers the top of the thermocouple and burns steadily with a yellow tip, that’s just about right.
Should a pilot light make noise?
If there is a roaring sound that occurs when the pilot light is on, it is usually because the flame needs to be adjusted. A grinding or shrieking noise is usually caused by a fan or blower. Newer gas fireplaces with blowers are usually a lot quieter than a lot of older fan systems, which can sometimes be quite noisy.
How do you fix a yellow pilot light?
If you notice that you pilot light is burning yellow instead of blue, contact Jerry Kelly. The issue can typically be fixed by cleaning out the air intake valve to the pilot light, which should only be done by a professional who knows how to access and repair the part.
What color should a pilot light flame be?
Inspecting a Gas Furnace Pilot Light Flame A natural gas flame should be a bright blue color with a small amount of yellow at the very tip. A propane flame will have more of a bluish-green flame with a tinge of yellow at the tip. The flame should strong enough to cover about 1/2 inch at the end of the thermocouple tip.
Why is my pilot light red?
Your Furnace Needs a Cleaning Your pilot light should be bright blue, not red or yellow. A red or yellow flame indicates that your pilot light isn’t getting enough fuel.
Why is my pilot light orange?
If your pilot light’s flame is orange or yellow, it is burning inefficiently due to a lack of oxygen. The thermocouple should sense when this happens because the heat from the flame will not be as hot as it should be.
How do you adjust the pressure on a gas fireplace?
If the pressure readings aren’t ideal, you need to turn the regulator by 90 degree turns using your flat head screwdriver. Turn it clockwise to increase pressure and counterclockwise to decrease pressure.
How do you fix a weak pilot flame?
The cause of a weak flame may also be an obstruction in the pilot tube. You can often remove such obstructions by turning off the gas, unscrewing the pilot tube from the valve control and blowing compressed air from a can through the tube. You can also poke the aperture of the pilot tube with a needle.
How do I know if my pilot light is bad?
The most obvious sign of the failure of a pilot light will be a lack of hot water or warm air since the burner assembly can’t light and do its job of heating these substances. In many systems, a broken pilot light will prevent the appliance from working at all.
Should the pilot light always be on in a gas stove?
Pilot lights and main burners on gas appliances should always produce a blue flame. If the flame is yellow or red, service is required as soon as possible.
How do you light a gas pilot light?
Once the gas has had time to dissipate, turn the knob to “Pilot.” Then, hold down the “Reset” button and bring the flame of a long lighter close to the pilot light opening. This should light the furnace pilot light. Once you are sure the pilot light is on, release your pressure on the reset button.
Does a gas oven have a pilot light?
Most newer gas ranges and ovens don’t have pilot lights. Instead, the gas is ignited by an electric ignition system. In this type of system, an element becomes hot and glows like the filament in a lightbulb when an electric current passes through it. The heat from the filament lights the gas.
How do you check the pilot light on a stove?
Below the stovetop, you will find gas lines connecting the burners; in the middle of each of those pipes is the port where the pilot light resides. If the mechanism is working properly, you’ll see a little blue flame there. Clean the pilot light area.
Where should the pilot light hit the thermocouple?
Remove the pilot tube from the gas valve and spray compressed air to clear it. When working properly in most gas appliances, the pilot flame should hit the upper 1/2 to 3/8 of the thermocouple. If the pilot has a weak, orange-yellow flame or barely reaches the thermocouple, it’s too low.
How do I stop wind noise in my gas fireplace?
What can be done about wind noise in a chimney? The simple answer is: stick a sheep in it! The thick layer of wool will muffle the sound. It will also cut off the flow of air that is being caused by the stack effect, diminishing the noise of roaring air as it flows up the chimney.
Why does my gas fire keep popping?
If you hear a popping noise when the burner’s on, it may indicate that there are small leaks around joints in the burner assembly. To test for leaks, first turn off the burner. Once the ceramic logs have cooled off, remove them from the firebox. Gas leaks are serious business and need immediate attention.
Why isn’t my gas fireplace lighting?
Check Your Igniter and Thermocouple If nothing is blocking the tubing, and gas is flowing out, there might be something wrong with the spark igniter and thermocouple. Make sure there’s no debris lodged between the two. If the pilot light ignites but doesn’t stay lit, you might need to replace the igniter.
