Table of Contents
Why is my craftsman riding mower cutting uneven?
If your riding lawn mower is cutting the grass unevenly, start by checking the pattern of the cut. Blade vibration also causes an uneven cut. To eliminate vibration, replace unbalanced blades and worn mandrels. Replace a worn blade belt because a worn belt won’t spin the blades correctly.
Why is my mower cutting lower on one side?
If the deck on your lawn tractor is lower on one side than the other, the result is an uneven cut. Leveling your tractor’s deck periodically smooths out your lawn. It only takes a few minutes and just a couple of common tools to level your lawn tractor deck.
What causes a riding lawn mower to cut uneven?
Uneven cutting is wavy or smooth troughs in the lawn surface. Uneven cutting is usually caused by mower deck damage or misadjustment.Uneven Cutting. CAUSE SOLUTION Mower spindle is bent or loose Repair or replace the spindle Blades are installed incorrectly Reinstall the blades correctly.
What are the height settings Craftsman mower?
For self-propelled Craftsman mowers, the height can be changed by raising or lowering the tire’s level using adjustable levers. These levers are located on the inside of each tire, which is attached to the notches. What is this? Shift the lever forward or backward to raise or lower the height of the particular wheel.
Should a mower deck be level?
Level the mower deck to ensure grass cutting height is even across the width of the deck. This will help ensure a smooth and seamless side-by-side blend between each row of freshly cut grass.
How do I get my mower to cut higher?
In order to increase your lawn mower height, adjust the lever next to each wheel one notch towards the rear of the mower. Move the lever as many notches to the correct cutting height you desire. If you move the lever towards the front of the mower, you will lower the lawn mower height.
Which side of a lawn mower blade goes up?
The wings of the lawn mower blade will be oriented up toward the mower deck and any writing on the blade will likely be facing away from the deck. If the blade bolt comes with a washer, its concave side will be facing the blade.
Why does my Craftsman riding mower leave a strip of grass?
A strip of uncut grass left in the middle of mowing rows could signal that your lawnmower’s blades are unbalanced or that one or both of them was installed the wrong way. Ensure that your mower’s blades are on correctly, that both are secured tightly to the mower deck and that both are balanced.
What is the lowest setting on a lawn mower?
If you don’t know what kind of grass you have, a good rule of thumb is to cut it at three inches or down to a minimum of 2 ½”, never removing more than one third of the grass blade at a time. Understanding your model of lawn mower and how your lawn mower height settings work is important if you want to use it properly.
How do you raise the height of a Craftsman riding mower deck?
Locate the attachment lift lever on the right side of the steering wheel. Press down on the plunger at the top of the lever, and move the lever forward to raise the mower deck or backward to lower it.
How do you measure lawnmower height?
Open up the door and stick the ruler inside to measure from the ground to the edge of the cutting blade. You can see that it’s about 2 inches off the ground. After you measure the height, you can make an adjustment to raise or lower the deck according to the type of grass in your yard.
Should the mower deck wheels touch the ground?
Mower deck gauge wheels should be properly adjusted to prevent scalping grass on uneven terrain. The bottom of the wheels should sit approximately 1/8-1/2 of an inch from the ground, depending on your cutting height.
How do you cut uneven grass?
Try to dive straight up and down across the slope. This will reduce the risk of tripping over, and it will also help in mowing across the challenging slopes. To avoid scalping at uneven grounds, raise the deck of the mower and cut the grass taller just before you reach the top of the slope.
Do mower blades need to be timed?
Premium Member. The blades are not timed and if you try to “time” them, they will move around on their own. the tips miss each other no matter how you orient them, so there is no need to worry about it.
Should the front of a mower deck be higher or lower than the rear?
For most effective results, a lawn mower deck should have a pitch of 1/8-inch to 1/2-inch between the height of the deck rear to the height of the deck front. In any case, the front of the deck needs to be pitched lower than the deck rear, but don’t pitch too much because deck pitch that’s too steep can scalp lawns.
What do I spray under my mower deck?
Graphite, silicone, or Teflon sprays are all sold as lawn mower deck sprays (although the all-purpose product probably works just as well). Cover the entire underside of a clean, dry deck, then let dry as directed on label instructions. The effect is similar to cooking spray, but should last longer.
