Table of Contents
How do you acid wash a Pebblecrete pool?
To acid wash your pool, simply mix a solution consisting of an equal part of hydrochloric acid (muriatic acid). Then, spray down the sides of the pool with this solution, scrub it for about 30 seconds, and wash it away with clean water to prevent etching.
Is it OK to acid wash Pebble Tec pool?
Because of the Valley’s hard water and high summer pool evaporation, we recommended you drain and acid wash your pool every two to four years to help remove excess calcium, algae and other contaminates that may lead to interior pool staining and that unsightly white ring on your pool tile and pebble-tec surface.
How much does it cost to acid wash a Pebble Tec pool?
Acid wash pebble pool surfaces and you – reduce the surface lifespan. Aside from treatment costs, an acid wash can be inconvenient and expensive. For example, an acid wash alone costs between $850-$4,000 depending on the size of your pool. Also, the prices change depending on the severity of the stains.
How do you remove calcium deposits from a Pebble Tec pool?
If your pool has calcium carbonate deposits, you can remove them with a pumice stone, stain eraser or scale remover. A pumice stone should only be used on hard surfaces, such as tile and concrete. Simply use the stone to scrub the deposits.
Can you use any muriatic acid in a pool?
Most experts agree that muriatic acid is the best option to lower the pH and alkalinity levels of your pool water. You can also use it to clean tiles, remove stains, dissolve calcium deposits, and kill any mold and algae leftover in your pool at the end of the year.
What is similar to muriatic acid?
Phosphoric acid is a good substitute for muriatic acid and in most situations will clean surfaces just as well with less risk. Phosphoric acid is a main ingredient in many commercial grout and concrete cleaners that are readily available to consumers.
How long after Pebble Tec Do you acid wash?
It is not uncommon to add acid (HCl) to the water daily for the first 2 weeks, and 2 to 3 times per week during the remainder of the 28 days. sand/dirt/construction residue does not adhere to the interior surface.
Is muriatic acid hydrochloric acid?
Muriatic acid is a form of hydrochloric acid, which has a pH of about 1 to 2. The only differences between hydrochloric acid and muriatic acid are purity—muriatic acid is diluted to somewhere between 14.5 and 29 percent, and often contains impurities like iron.
How do you acid wash a pool without draining it?
Recipe for a No Drain Acid Wash Add 16 oz of Super Stain Away per 10,000 gallons. Add 8 lbs of pH Decreaser (Sodium Bisulfate) per 5,000 gallons. Check Total Alkalinity to be sure it’s at zero; if not add more pH Decreaser. Brush pool several times per day, with a steel pool brush, Test water each day.
How do you remove stains from Pebble TECS?
Pour 1/2 gallon of warm water into a bucket. Add 1/2 gallon of white vinegar. Soak a sponge in the vinegar solution. Wipe down the Pebble Sheen surface to remove stains left by mold or mineral deposits.
How much is an acid wash?
Acid wash a pool: national average cost cost to acid wash a pool National Avg. Materials Cost per square foot $0.06 National Avg. Cost (labor and materials) for 300 square foot $131.79 National Cost Range (labor and materials) for 300 square foot $119.76 – $143.82.
How long after acid wash Can you swim?
According to Clean Pool and Spa, you should wait no less than two hours before swimming in a pool which has been treated with muriatic acid. According to the website, “If you pour muriatic acid in the pool and swim within 10 to 15 minutes you might get a ‘hot spot’ of acid that can burn you.”.
How much muriatic acid do you add to a pool?
Usually 2 cups of muriatic acid in a 24 hour period is safe to add to a pool at the one time. Factors determining how much acid to add are how strong the muriatic acid is and the volume of your pool. The stronger the muriatic acid (aka Hydrochloric Acid) is, the less you can add at once.
Will muriatic acid remove calcium deposits?
Muriatic acid is a strong hydrochloric-based acid, that is a great descaler. Because of the intensity of this acid, it has the ability to remove severe lime and calcium deposits found in pools and toilets. However, because of the potency of this cleaner, it can cause damage to the eyes and any exposed skin.
Can I use muriatic acid to clean pool tile?
Clean Tiles with an Acid Solution. When using chemicals to clean your pool’s tiles, you want to wear all the right protective clothing. Once you’re suited up, you can then mix 1 gallon of water with 1 gallon of muriatic acid. When mixing, you want to slowly add the acid into the gallon of water.
When should I add acid to my pool?
If you have a pH reading of 7.8 or higher, and an average size (15,000 gallons) in-ground pool, you should add 1/4 gallon (a quart) of muriatic acid, and re-test after the water has circulated for an hour.
Will muriatic acid clear a cloudy pool?
You may be able to clear the water by adding muriatic acid to lower the pH. If the pool is still cloudy after the pH is lower than 7.8, you probably need to floc.
