Table of Contents
Bolts Don’t Have to Be Extremely Tight It’s important to keep in mind that the toilet tank is not intended to take weight and strain. The tank-to-bowl bolts are merely there to ensure the rubber seal between the tank and bowl is snug and leakproof. Tank bolts do not need to be tightened to an extremely snug position.
Can toilet tank bolts be too tight?
If you tighten it too much, you can pull the closet bolt out through the flange, ruining the flange or breaking the porcelain. DO NOT tighten it as tight as it will go, like you’re building something or working on your car – you’ll break the flange, chip or crack the porcelain or both.
Is toilet tank supposed to wobble?
No, your toilet isn’t meant to wobble. It’s supposed to be sturdy and hold your weight comfortably. If your toilet is wobbly, you can check if some of the issues we’ve mentioned above might be the cause. If they are, you can try to DIY and if not, make sure you call on a professional plumber to fix it.
Are toilet bolts supposed to be loose?
If your toilet rocks or moves when you sit down, a loose bolt is probably the culprit. Over time, these bolts can slowly freeze to the nut, which makes tightening them a difficult job. If the bolts can’t be tightened because they are stripped, however, you will need to replace them.
Why is my toilet tank wobbly?
Toilets wobble when they aren’t held securely to the floor, and if you let the wobble persist, they can leak and give you more serious problems. More often than not, the wobble is caused by loose toilet bolts, but the flange may also be responsible. It may be corroded, broken or set too high.
Should a toilet sit flat on the floor?
Level the Toilet If it does not sit perfectly flat, it will rock and is more likely to leak over time. Getting the toilet shimmed before bolting it down will help ensure it does not come loose in the future.
Why does my toilet rock when I sit on it?
Toilets usually rock because they are not resting flush against the floor. Underneath the toilet base is a round toilet flange that connects the toilet to the drain pipe. If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side.
Why is my new toilet rocking back and forth?
One of the most common things that causes a toilet to rock back and forth are loose flange bolts. These are the bolts that hold the toilet down at an even level with the floor in your bathroom. A toilet does not screw directly into the ground. Instead, it screws into what’s called a toilet flange, or a closet flange.
What if toilet flange is too high?
When your toilet flange is too high, your toilet may leak water and rock back and forth when used. Both the leaking and the rocking can warp or break the floor. A leaking flange can also rot the subfloor and lead to the accumulation of mildew and mold.
How long should toilet flange screws be?
1 1/2 inch screws or longer is usually a safer bet if you are screwing into thicker boards. If the board is more shallow, then 1-inch screws will probably do the job for you.
Are toilet tank bolts standard?
Are Toilet Tank Bolts Sizes Standard? Toilet tank bolts help to seal your toilet tank such that it does not leak. They are durable and often in the same sizes and lengths. More often, toilet tank bolts are standard and will fit most types of toilet tanks.
How do I keep my toilet tank bolts from rusting?
Metal screws on a toilet seat can often rust, causing unsightly stains. To prevent the screws on the toilet seat from rusting, fill the holes with tub and tile caulking, then use a putty knife to level the caulking and allow it to dry before closing the lid.
Are tank to bowl gaskets universal?
The purpose of the tank to bowl gasket is to provide a leak free seal between the toilet tank and bowl. Manufactured in a high quality, chlorine resistant rubber, the Korky tank to bowl gaskets are universal to fit most toilet tanks. All kits are offered with and without tank to bowl hardware.
Should toilets be caulked?
Caulk keeps your toilet secure the floor, and avoids any chance of injury or toilet malfunctioning. It’s actually required by the International Plumbing Code to caulk a toilet to the floor, and now knowing the reasoning behind it, why would you not want to?Dec 13, 2021.
Does toilet flange go inside or outside pipe?
Install a toilet flange on the outside. This can be done with a hammer and chisel. If the flange is cast iron with a rubber gasket, you should be able to remove the cast iron with a hammer and chisel, remove the rubber gasket with a sharp knife, then replace the gasket and the flange.
How do I know if my wax ring is sealed?
Water around the Toilet Base The first sign of a bad toilet ring is water forming around the base of the toilet. To test that a bad seal is the problem, grab a couple of towels and wipe up the water. Go on with your day, checking periodically to see if the water has returned.
Can a toilet be moved 6 inches?
Yes, you can actually move a toilet. Even moving a toilet by a few inches without having to make a new hole in the floor is possible. You can use an offset toilet flange to move the toilet by a couple of inches on any side.
