Table of Contents
Can you over tighten a toilet to the floor?
If you tighten it too much, you can pull the closet bolt out through the flange, ruining the flange or breaking the porcelain. DO NOT tighten it as tight as it will go, like you’re building something or working on your car – you’ll break the flange, chip or crack the porcelain or both.
Should a toilet sit flat on the floor?
Level the Toilet If it does not sit perfectly flat, it will rock and is more likely to leak over time. To correct this problem, slip toilet shims between the base and the floor to stop the rocking before bolting it down.
How much should you tighten toilet bolts?
Because porcelain toilets are relatively brittle, it’s important to tighten toilet tank bolts carefully. The best way to do so is to hand-tighten the nuts on the tank bolts, then use a wrench to make a quarter-turn on each nut.
Can a toilet flange be level with the floor?
When you install your toilet flange, it should be installed on top of the finished floor, and it should also be installed perfectly level. If your flange sits even or below the floor, then it’s wrong. These rings will prevent the toilet from properly recessing into the flange. Instead, use a standard ¾ inch wax ring.
Why does my toilet moves side to side?
If the flange is a little higher than the surrounding flooring, the toilet becomes raised slightly in the center, allowing it to rock to either side. This problem can develop over time, such as when the wax seal becomes faulty or when a surrounding floor settles a little.
Why is my toilet loose from the floor?
Toilets wobble when they aren’t held securely to the floor, and if you let the wobble persist, they can leak and give you more serious problems. More often than not, the wobble is caused by loose toilet bolts, but the flange may also be responsible. It may be corroded, broken or set too high.
Can you use 2 wax rings when installing a toilet?
You can certainly install a toilet with multiple wax rings, in fact sometimes it is necessary to make sure you don’t have a leak. You can buy an extra-thick wax ring, or you can just buy two rings and stack one on top of the other.
What are the 2 bolts called that hold the toilet to the floor?
Securing your toilet to the floor are two long bolts (called closet bolts) that come up through the base of the toilet and are secured with nuts.
Does a toilet need to be bolted down?
5 Answers. The bottom of the flange needs to be sitting flush with (or not more than 1/8″ above) the finished floor or else the toilet will rock. The flange should be fastened to the floor. Dry fit the toilet to make sure it doesn’t rock.
Can you over tighten toilet tank bolts?
Do not over tighten or you will crack the tank or bowl even if they are not touching yet. Tighten them until they are good and snug and you can usually see the gaskets on the bolts have compressed some.
Is your toilet supposed to move?
If your toilet isn’t solidly fastened to the floor, there may be trouble in your future. Any movement of the toilet damages the wax seal. That leads to leaks and major repairs. To steady a rocking toilet, cut plastic shims to fit and slip them underneath (you may have to remove caulk before adding shims).
Should toilet flange be on subfloor or finished floor?
5 Answers. The toilet flange needs to be on top of the finished floor. Meaning the bottom edge of the flange needs to be on the same plane as the toilet. So if your toilet sits on the tile, the flange needs to be on top of the tile too.
Can toilet flange be lower than floor?
In a typical toilet installation, the floor flange that sits inside the drain opening below the toilet should be positioned so that its bottom surface rests flush against the finished floor or no more than 1/4 inch above or below the floor.
What do you do if the toilet flange is above the floor?
To use grout to fix your flange: Start by mixing your grout. Get your toilet in place and set your toilet on four rubber shims. Take your mixed grout and pack it into the gap. Wait 24-hours before the grout to dry. Once dried, remove the shims.
How do I stop my toilet seat from moving side to side?
How to Stop the Toilet Seat From Shifting Sideways Lower the seat and locate the two screw covers at the back of the seat. Put the flat-head screwdriver in the screw slot and hold it steady while you unscrew the nut from underneath the bowl. Remove the nut and bolt and take the seat off the bowl.
How do I know if my toilet is leaking from underneath?
The main signs of a leaking toilet may include a damp area on the floor around the bottom of the toilet, a spongy feeling in the floor at the bottom of the toilet seat, signs of dampness on the ceiling in the room underneath your toilet, or the occasional smell of sewer gas and the flooring coming up in the area around Oct 7, 2020.
Why are Japanese toilets on the floor?
Squat toilets are used in public toilets, rather than household toilets, because they are perceived by some as easier to clean and more hygienic, therefore potentially more appropriate for general public use.
Can you glue a toilet to the floor?
Remove the toilet and turn it on its side. Measure the depth and width of the gluing edge of the bowl. Next, move your caulk gun to the inset depth you just measured and apply caulk directly to the floor, maintaining the inset depth as you follow the tape. Install the wax ring and lower the toilet onto the flange.
How much does it cost to fix a wobbly toilet?
The national average price for repairs is $75 to $200, with most people paying $150 on average to replace the syphon.Toilet Repair Price by Type of Repair. Type of Repair Average Cost (Labor Included) Wobbly Toilet $60 – $150 Seal $60 – $150 Flush $75 – $200 Bowl $100 – $300.
