Table of Contents
The subfloor under the tile should be at least 1 1/8″ thick, with a minimum of 5/8″ thick exterior grade plywood topped by 1/2″ cement backer board.
Is 3/4 subfloor enough for tile?
Tile installed over wood floor systems MUST have a minimum of 1-1/4 inches of solid material beneath it. This means you can have a 3/4 inch wood subfloor covered by 1/2 inch plywood, cement board, or approved gypsum fiber underlayment.
How thick should a floor be for ceramic tile?
There is a very specific thickness that is required for floor tile. The average thickness for the floor tile is ½ inch to ¾ inch for each sq of tile. Contrasting with the wall tile which is 3 to 6 inches thick. But too thick floor tile may interrupt the doors from functioning.
What subfloor should be under tile?
Exterior plywood is an acceptable underlayment for tile and is preferred to interior-grade plywoods because the bonding adhesives used are waterproof. If water seeps through the tile installation to the underlayment, it will not cause the wood to swell, as happens with interior-grade plywood.
Can you tile 1/2 plywood?
To accommodate the 1/2 inch difference in floor heights, purchase or cut a transition strip of hard wood. According to the three most prevalent manufacturers of backer board in the US, no, 1/2″ ply is not acceptable. All of them require at minimum 5/8ths plywood.
How thick should a subfloor be?
The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch. There are several factors that determine what subfloor thickness is optimal for added benefits like insulation.
Do I need a membrane under tile?
If tile is laid directly on top of concrete, this expansion and contraction will cause stresses that fracture or delaminate the tile. Other less common and more challenging substrates like asphalt and metal require an uncoupling membrane to ensure the tile will adhere to these surfaces.
How thick should thinset be under tile?
Plan for a layer of thinset 3/16-inch to 1/8-inch thick beneath your tile. A 3/16-inch layer of thinset will be enough for tiles with a smooth back to bond the tile to the floor or backer board. For natural tiles with an uneven surface on the back, you may need to spread a 1/8-inch layer of thinset during installation.
How thick is a normal floor tile?
Tile Sizes Floor tile is usually 1/2 inch to 3/4 inch thick, manufactured in squares measuring 4 inches by 4 inches up to 24 inches by 24 inches. Other shapes are available, such as rectangular or subway tile, octagonal and hexagonal shapes.
Are thicker floor tiles better?
Thicker tiles are less likely to break or crack than thinner tiles because they’re stronger. You may want to choose thicker porcelain tiles for flooring, especially in high-traffic areas, because porcelain floor tile durability is important in preventing cracks and damage.
Can you tile directly on subfloor?
Tile can be laid on plywood. But do not install tile directly on the plywood subfloor itself. Use an intervening layer of a sheet of thinner plywood.
How thick is backer board for tile?
Half-inch cement backer board is ideal for most tiling jobs, including walls, floors, countertops, and ceilings. For flooring, the backer board should be installed over a 5/8-inch thick OSB or plywood base. For countertops, use 3/4-inch plywood beneath the backer board.
Can you use 1/4 inch cement board on floors?
1/4″ USG Durock® cement board is an ideal substrate for floor and countertop ceramic tile installations. The 1/4″ thickness helps eliminate transition trim when abutting carpet or wood flooring and minimize level variations with other finish materials.
Do I need cement board under floor tile?
Whenever you’re laying tile on a wood subfloor, you need to first install cement backer board. You also can’t safely install tile flooring over plywood subfloor or onto an unprotected wood floor. If you did, there’d be a serious risk of rot, water damage, warping and mold. Plus, your tile and grout would likely crack.
What thickness backer board should I use?
Walls: Use 1/2-inch or 5/8-inch-thick cement board, not 1/4-inch. The extra thickness is needed when spanning the studs and it provides a solid base for the tile. Countertops: 1/4-inch, 1/2-inch, or 5/8-inch-thick panels are all suitable for countertops.
Is it better to use OSB or plywood for subfloor?
The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.
What size screws 3/4 plywood subfloor?
You’ll want the screw to go about an inch past the plywood into the joist or underlying layer beneath it. So if your subfloor is 3/4 of an inch thick, any screw about 1 3/4 inches long will do the trick. If the plywood subfloor you’re placing is 5/8 of an inch thick, you need a screw about 1 5/8 inches long.
Should you nail or screw subfloor?
Ideally, nail down your subfloor using corrosion-resistant nails that will securely hold it in place and last a long time. Screws are a great alternative that you can easily remove, but they are not as sturdy. Screws are superior in terms of reducing floor squeaks, but the installation is slower.
