Question: How Thick Is The Subfloor In A Mobile Home

Table of Contents

Measure Your Subfloor Thickness Most subfloors are either 3/4″ or 5/8″ thick. You will use the measurement to set your circular saw to the proper height. One of the most tedious parts of replacing subflooring in mobile homes is the removal of the original sub-flooring.

How thick is the plywood on a mobile home floor?

The most recommended subfloor material is 5/8″ plywood.

What type of subfloor is in a mobile home?

Mobile homes and manufactured homes, for many years, constructed subflooring consisting of a glue and sawdust combination referred to as particleboard. Unfortunately, when it gets wet, it acts like a sponge. Soft spots, rot, warping, and bowing can be caused by even a small amount of dampness.

What is standard subfloor thickness?

Thicknesses for products used for subfloors are generally 23/32 inch (just under 3/4 inch), but thicker sheets are available where building codes call for them.

Can I put new subfloor over old subfloor in mobile home?

This is not always the case in a mobile home, however, where subfloors may be made of lesser-quality particleboard. Mobile home subfloor thickness may be of some concern, and installing plywood over this subfloor can give you a stronger base for your hardwood, laminate or carpeting.

How thick is the subfloor in an older mobile home?

What size plywood is best for subfloor?

The minimum thickness of plywood for subflooring is about 5/8 inch. Since it does not hold fasteners as well as plywood, OSB must be a little thicker, or at least 23/32 inch. There are several factors that determine what subfloor thickness is optimal for added benefits like insulation.

What is underneath a subfloor?

Underlayment The underlayment material is installed below the floor covering and placed on top of a sub-floor. Under the visible covering, there is a layer made of soft or foam-like materials with a thickness of between 1/4- or 1/2-inch.

What is the best material to use for subfloor?

Plywood is considered the most popular material used for subflooring, it has been used since the 1950s and remains one of the top choices for contractors. Standard plywood works perfectly fine as a subflooring material, but the best option is ¾” tongue-and-groove plywood subflooring.

Is it better to use OSB or plywood for subfloor?

The National Tile Contractors Association and the Resilient Floor Covering Institute both recommend plywood for subflooring and underlayment, because it doesn’t have the risk of swollen edges that OSB does. Plywood also has a slight advantage in stiffness, which means that subflooring panels need not be quite as thick.

How thick should subfloor be for laminate?

Plywood subflooring with a thickness of 5/8-inch or 3/4-inch is substantial for laminate flooring, though adding an underlayment of a thinner plywood provides additional support.

What size screws 3/4 plywood subfloor?

You’ll want the screw to go about an inch past the plywood into the joist or underlying layer beneath it. So if your subfloor is 3/4 of an inch thick, any screw about 1 3/4 inches long will do the trick. If the plywood subfloor you’re placing is 5/8 of an inch thick, you need a screw about 1 5/8 inches long.

What causes soft floors in mobile homes?

Sagging mobile home floors: are usually a result of water damage in mobile homes with particle board flooring that doesn’t hold up well when it gets wet. Moisture Barriers Stop moisture from developing directly on the mobile home floor boards and will not allow the floors to rot.

What should I put on my plywood floor?

Wallpaper as floor paper: For this stunning DIY finish, fill and smooth gaps in the plywood subfloor with fast-setting drywall compound and a trowel. Then put down wallpaper in your pattern of choice, followed by three or four coats of polyurethane or other clear hard floor finish.

How long do mobile home floors last?

When installed properly, a manufactured or modular home can last just as long as a regular home built directly on a construction site. And manufactured homes that follow HUD code can last anywhere from 30 to 55 years.

How far apart are mobile home floor joists?

Studs are the vertical boards and are normally 2″ x 4″ and spaced every 16″ in a manufactured home. That’s what the term 16″ OC, or ‘on center’ means in construction lingo. Better quality manufactured homes will have 2×6 studs and more affordable homes will have 2x3s.

How much does it cost to install plywood subfloor?

Cost to Replace, Repair or Install Subfloor The average cost to replace or repair a plywood subfloor in a 306-square-foot room costs $550, or between $500 and $600. The average cost to install a new plywood subfloor is $620, or between $570 and $720.

What is mobile home bottom board?

The black material enclosing the base of a mobile home is known by several names: bottom board, belly board or paper, black board, etc. Typically, the material used is asphalt-impregnated fiberboard or fiberglass, cloth or heavy tar paper and woven polyethylene. All serve the same purpose: Prevent moisture infiltration.

How do you make a mobile home look like a house?

You might have some work making your single-wide home look like a house, but the following strategies can help: Add a garage or outbuilding beside the home. Install a basement and foundation. Upgrade the style to include a higher-pitched roof. Extend the eaves. Add crown molding. Install larger doors.

What is a mobile home floor made of?

The flooring of a mobile home is made of several different components such as: wood board frames (floor trusses), installation filling, and a sub floor (made from plywood, particleboard, or oriented strand board). After, carpet, tile, or vinyl is usually installed over.