Table of Contents
Saws start to differ when you look at their blade diameter—commonly 10 inches or 12 inches. The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
Can a 10-inch miter saw cut 4×4?
It may surprise you to know that the answer in question to cutting 4×4 posts with a miter saw is a hard, YES! If you can give the blade more clearance, then it should be possible to get a clean single pass cut through a 4×4 post, even when utilizing a 10-inch blade.
How thick can a 10-inch sliding miter saw cut?
A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.
How thick of a board can a 10-inch table saw cut?
10″ (254mm) Dewalt table saws can cut up to 3-⅛” (79.4mm) deep at 90 degrees and a maximum of 2-¼” (57.15mm) deep at 45 degrees.
Can a 10-inch miter saw cut a 6X6?
A miter saw with a 10-inch blade installed can cut a 6X6 lumber piece, only it cannot do so with one single pass. To do this cut with a ten-inch blade you’ll need to follow several steps to complete your cut.
Is a 10 inch miter saw big enough?
10-inch Miter Saw The 10-inch blade cuts pieces that are up to 6 inches wide, which covers most trim and molding boards. Trim is seldom more than 4 inches, so you’ve got plenty of wiggle room with a 10-inch miter saw. A 10-inch blade will spin faster than a 12-inch blade, resulting in smoother cuts.
Can you put a 12 inch blade on a 10 inch table saw?
No. A 10 inch table saw is just big enough to accept a 10 in blade. 12 inch blades are too big to fit a 10 inch table saw.
Will a 10 miter saw cut a 2×10?
The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees. The sliding action can cut even wider boards.
Can a miter saw cut a 2×10?
Miter Saw Limitations The biggest drawback of a miter saw is that the smaller (and cheaper) sizes can’t cut completely through wide material, such as 2×10 or 2×12 boards, in one pass. Well, a sliding miter saw can make these cuts, but you’ll spend twice as much for one.
How deep can a 10-inch radial arm saw cut?
The size of the blade determines the possible cutting-depth of the saw. A 10-inch saw blade cuts to a 3-inch depth.
What size blade does a 10-inch table saw use?
As long as the diameter of the arbor hole on the stacked dado blade set matches the arbor diameter of your table saw or radial-arm saw—and the arbor is long enough for a dado blade—you can use an 8-inch dado blade on a 10-inch table saw.
How deep can a 14 inch table saw cut?
In most cases, a table saw capacity is about 1/3 the diameter of the blade. Since there are machines that use blades as small as 6″ and as large as 20″ (or more) it is impossible to give one number. For example, a 14″ blade might allow a 4″ maximum depth of cut while a premium 10″ saw might allow a 3–1/4″ depth.
Can you cut crown molding with a 10 inch miter saw?
The Craftsman Professional” 10″ and 12″ Compound Miter Saws require you to do virtually no math to cut crown moldings. Extension bars on the 12″ that let you cut 2×8’s (2×6’s on the 10″) and positive dual bevel stops at 0, 33.9 and 45 degrees left and right mean you can cut big pieces without flipping them over.
What is a 10-inch miter saw good for?
Common Uses for a 10-Inch Miter Saw Perfectly angled miter cuts. More complex bevel and compound angle cuts. Cutting plastic and metal pipes to length. Precise repeated cuts.
Can I put a 10 blade on a 12 miter saw?
Yes, as the max size on on a Miter Saw that was sold with a 12 in blade should accommodate a 10 in blade !.
What size Mitre saw for trim work?
If you only expect to use your miter saw for cutting trim or siding, and don’t plan on cutting anything more than an inch thick or 6 inches wide, a 10-inch miter saw should be sufficient. But if you need to cut larger boards, or just want more versatility, a 12-inch miter saw is the better choice.
Can you put a 7 blade on a 10 miter saw?
Yes you can. But, the RPM of a smaller blade will be the same as that of a larger blade, and in fact the cutting edge will be moving slower. In other words: the blade isn’t in danger.
