Table of Contents
The average cost to power wash a deck ranges from $119 to $244 with most homeowners paying around $0.35 per square foot. To power wash, stain, and seal your deck, expect to spend between $0.50 and $1.50 per sq. ft. or $0.95 per sq.
How much does it cost to powerwash a 12×12 deck?
The average cost to power wash, stain, and seal a deck is $1.57 to $4.04 per square foot. A 12×12 deck costs $226 to $582 to stain when paying someone, or $59 to $176 to stain it yourself. A gallon of stain costs $20 to $50, which covers 200 to 300 square feet.
How much does it cost to clean a deck?
The average cost to pressure wash a deck ranges from $100 to $200 with the average homeowner spending around $145 to effectively pressure wash a 500 sq. ft. deck.Price to Pressure Wash a Deck. Deck pressure washing cost National average cost $145 Average range $100-$200 Low-end $87 High-end $766.
How do you quote a deck for power washing?
Power washing houses usually costs between $220 to $380, a driveway costs $130 to $220 and a deck or patio costs $250 to $420. The price depends on any cleaning chemicals that might need to be used and the size of the surface. Power washers usually price jobs by the square foot, the hour or using a flat rate.
Can I just power wash my deck?
A pressure washer is a straightforward machine that can clean very well with only water. However, it can ruin your deck if it’s not used properly. If you use it with too much jet pressure or place the tip too close to the surface of your deck, you can deeply etch the wood and cause the fibers to splinter.
How long should it take to power wash a deck?
When pressure washing, saturate the deck with deck detergent, give it 15 minutes to work, then begin power washing. Follow the operating directions for your power washer. After completing the deck power washing, wait 24 to 36 hours before applying sealer. If the weather is cool or humid, wait 48 to 72 hours.
Should I pressure wash deck before staining?
There is a common misconception that just pressure washing a deck prior to staining is all you need to do in order to prep your deck for stain. Pressure washing can help, but if you want your stain to last, using a good deck cleaner and brightener on the deck prior to pressure washing will provide you the best result.
How do I clean my deck without a pressure washer?
The recipe is pretty straightforward: Add half a cup of baking soda to one gallon of water; Mix in 1/8 of dish-washing detergent; Spray on your concrete deck and allow it to sit for half an hour; Scrub thoroughly and rinse with a hose. Apply a coat of concrete sealer to protect your deck from future stains.
Is deck Cleaner necessary?
In short, yes. It is highly recommended to use a deck cleaner when prepping your deck for a new coat of deck stain. Also, recommended but not required is the use of a deck brightener before staining your deck. These deck cleaning solutions will soak down into the dry wood.
How much to pressure wash around a pool?
Expect to pay between $0.20 to $0.40 for most outdoor concrete surfaces including pools, patios and walkways.
How many square feet can you pressure wash in an hour?
Just talking surface machine cleaning per hour and not Gum removal which can take alot longer, we use anywhere from a 24″ surface machine all the way up to a 48″ machine. All Powerwashers are 8gpm on up with hot water. I’d say per man we can range from 3000sq’ per hour up to over 10,000sq’ per hour.
Is it OK to waterblast a deck?
Be careful. And PLEASE, do not waterblast your deck, no matter what the manufacturers of overpriced cleaning gadgets tell you. Powerful jets of water can damage your decking timber, lifting timber fibres.
Is 1800 psi enough to clean deck?
For cleaning a wooden deck, you’ll be best served by using the lowest pressure setting that’s still effective. For soft woods like cedar or pine, this is usually about 500 to 600 psi. For harder woods, it can go up to 1200 to 1500 psi. Never get closer than 12 inches from the deck unless you’re using low pressure.
What if it rains after I power wash my deck?
If it looks like rain, cover the deck in a tarp to avoid extra seepage. If standing water is left after you power wash and scrub the deck, squeegee it off the surface of the wood or soak it up with towels to avoid soaking into one place.
Can you jet wash decking?
Jet washing is a popular choice for removing flaky or peeling sealers. You can use a jet washer to clean decking finished with oils too, but you need to take care not to push the existing finish out of the wood and into surrounding plants, ponds or soil.
Is it better to sand or power wash a deck?
DO sand your deck before sealing. At that point, lightly sand the surface to remove splintery or fuzzy patches caused by pressure-washing the deck. A pole sander with 80-grit sandpaper will suffice; a power sander is overkill. Then seal the deck to protect from cracking, cupping, and warping.
