Table of Contents
Most concrete driveway installation costs between $1,800 and $6,000 or $4 to $15 per square foot. The average is just above $3,000 or $6 per square foot. Factors like location, size, decorative elements, potential reinforcement and removing the existing surface can all influence that range.
How much does it cost to pour a 24×24 slab of concrete?
A typical 24×24 garage slab costs between $3,057 and $5,944 with prices ranging from $5.31 to $8.31 per square foot for a 4” reinforced slab of concrete, and $6.83 to $10.32 per square foot for a 6” slab of reinforced concrete.
How does it cost to concrete a driveway?
Cost of a Concrete Driveway. A concrete driveway costs from $8 to $18 per square foot, depending on decorative colors and finishes. While a plain gray concrete driveway costs between $5 and $7 per square foot to install. Concrete is ideal for getting the look of stone or pavers, without the high cost.
Can I pour my own concrete driveway?
It’s easy to pour and build a concrete driveway made of cement. You can build an attractive concrete driveway yourself, but careful planning and preparation is necessary. Be sure to place all the concrete at once; a big driveway can be broken down into smaller manageable sections using 2×4’s.
How thick should a concrete driveway be?
As for thickness, non-reinforced pavement four inches thick is standard for passenger car driveways. For heavier vehicles, a thickness of five inches is recommended. To eliminate standing water, the driveway should be sloped towards the street a minimum of one percent, or 1/8 inch per foot, for proper drainage.
How much concrete do I need for a 30×30 slab?
18 yards of 3000 psi concrete mix @ 135.00 per yard. Wire mesh reinforcement. A double row of #4 rebar around the edges. Labor to form the slab.
How many yards of concrete do I need for a 24×24 slab?
For example, for a concrete slab that is 24′ X 24′ X 4”, simply enter 4 in the Thickness/Depth field, 24 in the Width field, and 24 in the Length field. Click “Calculate”. Your answer should be 7.11 yards. Note: The Concrete Volume Calculator can also be used to determine yardage for aggregate products.
Is concrete or asphalt better for a driveway?
Concrete is more durable than asphalt. Because it is a less flexible material, it cracks in freezing temperatures, and many people turn to concrete patching products. Concrete offers 50+ years of use. The only maintenance required is occasional degreasing.
How wide should a driveway be?
How Wide Are Residential Driveways? Primarily, most professionals recommend that you install a 10 feet to 12 feet wide driveway. The standard driveway width for an SUV or conventional pickup truck is 10 feet. Anything less than 10′ wide will likely present difficulties for drivers, even in smaller vehicles.
What is the cheapest way to do a driveway?
Gravel and Stone Driveways A gravel driveway is by far the cheapest and quickest to install, especially if the existing driveway sub-base is sound.
HOW MUCH CAN 4 inches of concrete hold?
Typically we like to limit the weight to about 40 lb/sqft on an unknown 4″ slab. In most cases you can go to 80 lb/sqft in isolated spots, but unless you know roughly what the soil bearing and reinforcing is for that slab you might be looking at cracking.
Is rebar needed in concrete driveway?
The presence of rebar in a concrete project gives the final project considerably more strength than concrete alone. This strength is crucial for things like buildings, roads and driveways. Rebar is not necessary for every concrete project. Wire mesh use is becoming much more common for projects like a home driveway.
Do you need gravel under concrete driveway?
Whether you pour concrete for a walkway or patio, a strong gravel base is required to prevent the concrete from cracking and shifting. Gravel is especially important in clay soil because it doesn’t drain well, which results in water pooling under the concrete slab and slowly eroding the soil as it finally drains.
How many pounds can a concrete driveway hold?
A 3,000 psi slab should support 3,000-pounds but if you’re concerned about cracking, limit it to its 300 psi tensile strength. What is this? Most residential driveways typically use concrete compressive strengths of 3,000 to 4,000 psi and commercial and industrial 5,000 psi.
Do you need wire mesh in concrete driveway?
When it comes to concrete, you can’t avoid cracks entirely, but wire mesh reinforcement will help hold the material together when they do occur. Also, it will help evenly distribute the weight of cars on your driveway. The added strength of steel is especially crucial if your subgrade isn’t up to par.
How many yards of concrete do I need for a 10×10 slab?
The amount you will need for a 10 x 10 slab is 1.3 cubic yards, we always add an extra 10% to allow for any slab depth variations or spills that may occur.
How much does it cost to pour a 20×20 concrete slab?
But how much does a 20×20 concrete slab cost? You can expect to pay between $1,600 and $3,200 for a 20×20 slab. The estimates are based on the average cost of $4 to $8 per square foot for a concrete slab. Yet, the costs may vary.
How many bags of concrete do I need for a 10×8 slab?
Regarding this, “how many bags of concrete do I need for a 10×8 slab?”, at 4 inches thick, generally you will need approximately either 58 bags of 60lb or 45 bags of 80lb of premixed concrete for a 10×8 slab, at 5 inches thick slab, either 73 bags of 60lb or 56 bags of 80lb premixed concrete are required, while at 6.
