Table of Contents
Well Drilling Costs By State State Average Cost Per Foot Maine $27 – $58 Maryland $29 – $62 Massachusetts $31 – $69 Michigan $28 – $62.
How much does it cost to put a well in Maine?
Our per-foot well drilling prices sometimes change due to the fluctuating cost of casing and other materials. Although it is impossible to tell exactly how much a well will cost beforehand, most water wells including the pump system cost between $6,500 – $8,500.
How deep is the average well in Maine?
The average depth for a drilled well in Maine is about 250 feet.
Do you need a permit to drill a well in Maine?
Pretty much unregulated – no State permit is required. Well drillers are licensed and regulated by the Maine Well Drillers Commission.
How much does it cost to put in a drilled well?
Most well drillers also have a minimum charge, usually around 100ft minimum which at $45 per foot would be $4500. Drilling a water well is a long term investment and most people are reluctant to drill without knowing if they will find water, and if so at what depth.
How deep are drilled wells in Maine?
Most dug wells in Maine typically have depths of approximately 15 feet, with some extending to as much as 60 feet.
How much does it cost to put in a septic system in Maine?
Keep in mind that a septic system costs less than $300 to pump but $12,000 or more to replace and can affect the resale of your property. If your system shows signs of failure, is in coarse, sandy soils, or is within 100 feet if a lakeshore or stream, plan to replace it.
How do I find the water table in my area?
How to Find My Water Table Call your local County Extension Office. It may have statistics for the average annual water table level in your area. Look online. Check out the website for your local Water Resources Office. Dig. This is the most reliable way to find the water table level on your land.
How close to a property line can you drill a well?
As a general guidance, personal drinking water wells should have a minimum horizontal distance of at least 10 feet and preferably 25 feet from such boundaries.
How far does a well have to be from a septic system in Maine?
The Maine Department of Human Services recommends at least 100 feet of horizontal separation between a private well and a private septic system(s), with greater setbacks for public wells and/or large septic systems.
How close can you build to a well in Maine?
Table 400.1 Depth of Well Casing or Liner Seal Below Ground Level Minimum Setback Distance for Disposal System < 2,000 gpd Minimum Setback Distance for Disposal System > 2,000 gpd 40 feet 90 feet 270 feet 55 feet 80 feet 240 feet 70 feet 70 feet 210 feet 90 feet 60 feet 180 feet.
How long does it usually take to drill a well?
When all is said and done, the entire water well installation process takes about one or two weeks. This is usually quite surprising to those looking to drill a well. You can go from untouched earth to a fully functioning water well in no time!Nov 5, 2018.
Can a well be drilled in the winter?
Drilling a well in the winter is often less muddy, less messy, and is a good way to avoid damaging your lawn during the months when you actually want to enjoy it. Your water will be ready to go.
Why is well drilling so expensive?
The drilling depth to water and bedrock and the well’s diameter are the most significant cost factors. The average well is drilled 100 to 300 feet deep, while some shallow wells only go down to 25 feet to reach groundwater.
How deep should a well be for drinking water?
The quality of your water depends on several factors including geology and water levels. In order to allow for maximum ground filtration to remove impurities, your well depth should be at least 100 feet. As a general rule, the deeper you drill, it’s more likely that there will be minerals present.
Is 20 gpm good for a well?
You could have a great well water flow rate – say 20 gallons per minute – but if it the water will only run at that rate for five minutes before you run out, the well has a very poor water quantity (5 minutes x 20 gpm = 100 gallons of water) and it’s not a satisfactory well.
How deep should a dug well?
To minimize water quality and quantity impacts, dug wells should be at least 3 m (10 ft) deep and sited away from surface water sources. Surface water can carry contaminants from the land surface into your well and the aquifer.
Do people still dig wells?
Driven wells are still common today. They are built by driving a small-diameter pipe into soft earth, such as sand or gravel.
Can I install my own septic system in Maine?
Septic system design in Maine must be done by a licensed site evaluator. Contractors are not required to be certified in the installation of septic systems and, in fact, a property owner is entitled to construct their own system.
Are plastic septic tanks legal in Maine?
Maine Septic Tanks Save up to 50% on plastic septic tanks. These septic tanks are state approved for use in the state of Maine.
How much does a new leach field cost in Maine?
Although costs vary according to the size of the leach field, soils and costs of local permits, expect to pay between $5,000 and $20,000 for leach field replacement. It is the most expensive component of the septic system.
How deep is the average well?
Most household water wells range from 100 to 800 feet deep, but a few are over 1,000 feet deep. Well yields can be increased by fracturing the bedrock immediately around the drill hole and intercepted rock faults.
How do I know how deep my water table is?
The most reliable method of obtaining the depth to the water table at any given time is to measure the water level in a shallow well with a tape. If no wells are available, surface geophysical methods can sometimes be used, depending on surface accessibility for placing electric or acoustic probes.
