Table of Contents
Proper deck board spacing should have a 1/8-inch gap after the decking has dried out. If you install your decking using wet boards, pressure-treated decking that has not yet dried out, then you should install them with no gap as a gap will be created as they dry and shrink. Deck spacing isn’t anything to take lightly.
Should deck boards be butted together?
We recommend butting treated deck boards together because as the moisture dries from the wood, the boards will shrink and naturally form gaps to allow water drainage. (Depending on moisture content, cedar, cypress and especially hardwood decking may require deliberate spacing for consistent joint sizes.)Jun 21, 2010.
Should you space treated deck boards?
Leave a gap between pressure treated deck boards when the wood is wet. Leave Gap: If the pressure treated wood has been kiln dried after treatment (KDAT), leave a 1/8” gap (the thickness of an 8-penny nail) between the boards when attaching, since the wood will expand slightly over time.
Is 3/16 gap between deck boards okay?
The Sweet Spot – Most people agree that 3/16” is a good gap between boards. Going more than a ¼” may get a little too wide. The width of a nail head is just about right. Treated Lumber – Usually treated lumber will have some shrinkage so you can butt the boards almost right against each other during installation.
What is the correct way to lay decking boards?
What is the correct way to lay decking? Any decking board manufacturer or professional will tell you: “The proper way to install a decking board is ridge side down.” The ridges are designed to allow for airflow, to stop moisture sitting in the ridge, and allow for a stronger structure.
Do you screw decking at every joist?
Each deck board should be fastened with two screws at each point where the board crosses a joist to ensure the stability and durability of your deck’s surface. Boards should be fastened to rim joists with three screws.
Do deck boards shrink or expand?
Any type of decking board will expand and shrink, whether it’s wood, plastic, or composites. However, they don’t change in size as much as wood or plastic. Wood fibres hold the shape when the composite undergoes thermal expansion, while the plastic fibres do the same when moisture is involved.
Should I Space 5 4 decking?
For 5/4 pressure treated decking, it should be installed tight and allowed to shrink to provide water drainage. With cedar 5/4 decking installation should be with 1/16″-1/8″ gap (2-3mm), which will expand to 1/8-1/4″ (3-6mm) once the wood has dried. Providing both deckings’ plenty of spacing for drainage.
How do you stagger deck boards?
A common method for staggering a deck is to start the first row with a full plank, then cut one-third of the next row’s first board off the end. The row after that has an additional one-third cut off and then repeat when you get back to a full board.
Can you put deck boards tight together?
Keep the butt ends as tight as possible when installing wood decking. This rule does NOT apply to composite or PVC boards which can have a large thermal expansion; enough to create a serious roller coaster effect down the length of the PVC or composite boards if you DON’T leave room for thermal expansion.
How many decking boards do I need for a 10×10 deck?
For a 10×10 square deck, you would therefore need twenty-two 10′ deck boards. Dimensions for deck boards can vary depending on the look you want and the deck board type you use. However, the most common is a 5/4” thick by 6” wide deck board of any length.
How do you fill space between deck boards?
While you might be tempted to fill in gaps in your decking with wood filler or caulk, the natural movement of the boards can eventually cause the materials to break loose and make the gaps even worse. However, you can use rope to easily fill the gaps.
Should you stagger decking boards?
Staggering the deck boards decreases the number of screws or nails going into one joist, which can weaken or rot the joist more quickly. Staggering the joints strengthens the deck by spreading the seams across more joists instead of placing the stress on only one.
Can I use 4×2 for decking frame?
4 x 2 Timber Rail / Joist. These decking joists are the most common sized framing timber for decking. They provide a solid structure for fixing your decking boards too. When making your decking frame you should use a 400mm spacing between your timber joists.
Should deck boards run parallel or perpendicular to house?
Decking running parallel to the house makes the deck look wider and blends the deck into the house. If the decking runs perpendicular, the deck looks long and extending far out, away from the house.
Which side of deck board should face up?
Lay deck boards so that the best-looking face is facing up! Wood is stable when its moisture content is held above 30%(fiber saturation point). As wood dries below 30% it shrinks. Wood shrinks and swells twice as much in the direction parallel to the growth rings as it does perpendicular to the growth rings.
Should deck boards be installed crown up or down?
Crown up is the preferred installation method, despite the potential for bark side down deck boards to experience shelling. Bark side down allows for the formation of a crown warp. Once the board forms a crown, there’s less potential for the wood to hold water, which could lead to the wood splintering and rotting.
