Table of Contents
Place approximately 5 feet of tar paper at a time. Overlap each piece 2 inches over the piece before it. This ensures a secure barrier against moisture.
How much should roofing felt overlap?
Always ensure there is at least 5cm of overlap between each sheet, and nail down the felt from the centre outwards as before.
What are the lines on tar paper for?
There are pre-printed lines on the tar paper that help show you where to end the overlap. Usually 2 inches is plenty on a horizontal seam. If you have a vertical seam where one piece ends and another starts, make the overlap at least 6 inches.
How long should tar paper staples be?
Tack or fasten roofing felt using stainless steel ¼” to ½” T50 staples or 7/8” to 1-1/2” hot-dipped galvanized or aluminum 12-gauge shank roofing nails with a 3/8” head diameter. Use the nails with or without plastic caps.
Do you overlap roofing felt?
Remember to leave a 2″ overlap. Drive about five nails in the top right-hand corner and roll out the felt about halfway (perhaps 25 feet) across the roof. Stand on the first course of felt and work with the second course of felt above you. It is not necessary to completely nail the top edge of the course.
Can I put 2 layers of felt on shed roof?
So it is possible to have 2 layers of felt in General. For instance, an alternative to 30# felt is to put two layers of 15# felt, or often 2 layers are recommended on a 2/12 pitch roof. In the “good Old Days” it was often doubled up to help resist ice dams (now delt with by Ice and water Shield).
Which side of tar paper goes down?
When laying sheets of tar paper, always lay the sticky, glossy side down. Tar paper’s two sides are noticeably different. One side is somewhat sticky, though don’t expect it to leave a glue-like residue on your hands. The other side is smooth like paper, and typically contains lettering and line markings.
How do you fasten tar paper?
Tack the tar paper in place with a hammer tacker with roofing staples. Alternatively, you can use galvanized nails and a hammer or an electric staple gun with roofing staples. Space out the nails and staples along each edge, and scatter some along the interior of the tar paper strip.
Do you install drip edge before tar paper?
The best way is to install the roof drip edge only along the eaves first, then place ice-and-water barrier (in the snowbelt) or felt paper (underlayment) over the drip edge.
How much do you overlap underlayment?
Overlapping 19 inches will ensure that the underlayment is at least two layers thick all over the roof. So, underlayment on low-slope roofs should overlap 19 inches. Remember that underlayment on steep-slope roofs should overlap 2 inches.
How many inches do you overlap metal roofing?
Install Metal Panels Align the first metal roofing panel so that it overlaps the edging by 1/2 to 3/4 of an inch and is square to the roof line. Be sure the larger edge is laid so that the small edge of the next panel will overlap it.
Should I use 15 or 30 lb felt?
If your roof does not have a steep pitch, you can use #15. This weight of felt is a good economic choice if you have a standard roof. But if your roof has a steep pitch, #30 is a better option because it is thicker and tears less during installation. With #30 you get a thicker layer of underlayment and protection.
Can you felt over old felt on a shed?
Many people ask if you can felt over old felt. We would advise stripping the roof so that you can inspect and repair the roof timber before then laying down a new layer of roofing felt.
Do you need adhesive for shed felt?
The reason you should use adhesive sparingly is because the bitumen in the shed felt will expand in warm weather and it will contract in cold weather. Not using too much adhesive allows it some give, which prevents it from tearing or cracking.
Does shed felt need underlay?
You can increase the lifespan of new shed felt by using a method that is also used to protect the roofs of other buildings and structures when they have a pitch of less than 20 degrees. To use this method, you will need to use an underlay, which will need to be put in place before you install the shed felt.
Can you staple tar paper?
Installing roofing felt, or “tar paper,” is an important step when roofing a building. Some roofers prefer to attach felt underlayment with 1-inch roofing nails or special nails with plastic washers, but most codes allow staples, which are easier to drive.
How do you attach tar paper to a wall?
Hold a roll of felt paper against the left edge of the wall, with the top end of the roll aligned with the chalk line. Tack the end of the paper to the wall using a construction stapler. Then roll out the paper along the wall, keeping the top aligned with the chalk line.
