Table of Contents
0.58 US qt GCV160 GCV190 Fuel Tank Capacity .98 U.S. qts (.93 liter) 0.98 U.S. qts (.93 liter) Fuel Unleaded 86 octane or higher Unleaded 86 octane or higher Oil Capacity 0.58 US qt (0.55l) 0.58 US qt (0.55l) Lubrication System Splash Splash.
How much oil does a Honda GC160 take?
Features GC160 GC190 Fuel Tank Capacity 1.9 U.S. qts (1.8 liters) 1.9 U.S. qts (1.8 liters) Fuel Unleaded 86 octane or higher Unleaded 86 octane or higher Oil Capacity 0.61 US qt (0.58l) 0.61 US qt (0.58l) Lubrication System Splash Splash.
What kind of oil does a Honda GCV160 take?
Oil. Honda recommends 10W30, but 5W30 can also be used, or SAE 30 so long as temperatures are above 50 degrees F (10 degrees C.)Jan 18, 2017.
How much oil does a Honda lawn mower need?
The amount of oil left in the engine varies. If you don’t use the supplied oil, add enough SAE 10W-30 API service category SJ or later oil to bring the oil level between the upper and lower limit marks on the dipstick—without screwing the dipstick in (approximately 12 to 13.5 ounces is required).
How much oil does a Honda GCV 170 take?
GCV170 Fuel Unleaded 86 octane or higher Oil Capacity 0.42 US qt (0.41l) Lubrication System Splash Dry Weight 22.3 lbs (10.1 kg).
How much oil does a Honda power washer take?
Honda 10W30 4-Cycle Engine Oil (1 Quart).
Does Honda recommend synthetic oil?
Can I use synthetic oil in my Honda engine? Honda engines are developed, tested and certified with petroleum based motor oils as a lubricant. Synthetic oils may be used; however, any motor oil used in our engines must meet all oil requirements as stated in the owner’s manual.
Is SAE 30 the same as 10w30?
SAE 10w30 oil has 10w thickness at low temperatures, but SAE 30 is at high temperatures. In the straight SAE, 30 doesn’t and can have immense Viscosity and helpless pumpability at low temperatures. As SAE 10w30 is not thick in low temperature, while SAE 30 is in high temperature.
How many ounces of oil does a Honda push mower take?
The amount of oil left in the engine varies. If you don’t use the supplied oil, add enough SAE 10W-30 API service category SJ or later oil to bring the oil level between the upper and lower limit marks on the dipstick—without screwing the dipstick in (approximately 12 to 13.5 ounces is required).
How much oil does a hrx217 take?
Honda’s HRX series of push mowers, including models HRX217HXA, HRX217HMA and HRX217TDA, are equipped with Honda’s GCV190 engine. This 6.5-horsepower engine holds 0.58 quarts of oil (18.6 ounces) and does not have an oil filter.
How often should you change oil in Honda lawn mower?
Honda recommends an oil change after every 50 hours of use unless the mower is brand new, in which case its oil will need to be changed after just 5 hours of initial use. When changing the mower’s oil, remember always to use a high-detergent oil made for 4-stroke engines.
What spark plug does a Honda GCV160 take?
Honda 98079-56846 (BPR6ES) Small Engine Spark Plug for GCV160, GCV190 Brand Honda Core Material OEM HONDA “MADE IN JAPAN” RETAIL PACKAGING Thread Size OEM HONDA “MADE IN JAPAN” RETAIL PACKAGING Top Material Type OEM HONDA “MADE IN JAPAN” RETAIL PACKAGING Vehicle Service Type OEM HONDA “MADE IN JAPAN” RETAIL PACKAGING.
How much oil does a 5.5 Honda take?
Engine Type Air-cooled 4-stroke OHV Air cleaner Dual Element Oil Capacity 0.61 US qt. (0.58 L) Fuel Tank Capacity 3.3 U.S. qts (3.1 liters) Fuel Unleaded 86 octane or higher.
What type of oil does a Honda GX160 take?
10W/30 API Model GX160 PTO Shaft Rotation Counter-clockwise (from P.T.O. side) Fuel Consumption at Rated Power 1.4 L/h at 3,600rpm Lubrication System Splash Recommended Oil 10W/30 API SG.
How much oil do I put in my lawn mower?
Most small engines need 20 to 24 fluid ounces of oil. Small engines typically use SAE 30 single-weight detergent motor oil service-rated SG or higher, but some can use multiviscosity oils such as 10W-30 or 10W-40. Fill the crankcase slowly. Keep tabs on the oil level by checking with the dipstick as you add oil.
What oil goes in a Honda pressure washer?
Replace the oil drain plug. Refill with SAE 10W-30 oil (the amount will vary by model, so check your owner’s manual for capacity) and replace the oil-filler cap.
How often should I change the oil in my pressure washer?
A pump oil change should be done every 3 to 5 months to keep equipment running smoothly, safely and efficiently. The high pressure pump inside a hard working pressure washer is literally the heart of the machine.
How do you add oil to a pressure washer?
Start by running your pressure washer for a couple of minutes to empty dirt and water. Then empty the remaining oil from your pump into a tray. Use a funnel to add your new oil, non-detergent-based, into your pump until about ¾ of the way full. Close your pump firmly and set your pressure washer in an upright position.
Can I switch from synthetic oil to regular oil?
When it comes to doing oil changes, switching between synthetic and conventional oil is perfectly okay. Despite the oil myths, both oil types are compatible with each other – no engine flush needed. So, simply making the switch will not cause any damage to your engine nor impact your travels.
Who makes Honda full synthetic oil?
Idemitsu brought 0W-20 stateside in 2010. Since then, it has been the factory-fill oil of millions of Honda, Toyota and Nissan vehicles made in America.
Can I mix synthetic oil with regular oil?
Mixing them will not improve the performance or efficiency of your engine in any way. Adding synthetic oil to regular motor oil will not enhance the regular oil. Mixing regular motor oil with synthetic oil may dilute the benefits of the costlier synthetic oil.
