Table of Contents
Blown-in insulation cost ranges from $930 to $2,085, with most homeowners paying a national average of $1,507. Like other types of insulation, such as fiberglass batts and spray foam, blown-in insulation reduces thermal transfer from outside to inside.
Is blown-in insulation cheaper than rolls?
The Differences Between Blown-in and Rolled Insulation The lower the R-value is, the less effective it will be as insulation – although it will be cheaper as well. In such situations, blown-in insulation is much more effective since it allows you to easily insulate those hard to reach areas.
Is blown-in insulation expensive?
Blown-in cellulose is often more expensive than fiberglass and costs about $1.20 per square foot. The cellulose insulation cost per bag is typically around $30 to $40. It is made with recycled materials like newspaper and cardboard. The higher the R-value, the more you’ll pay for each project.
Is blown-in attic insulation worth it?
Unless your home is relatively new, you will almost certainly benefit from installing blown insulation in your attic. It will make your home a more comfortable place to be in summer and winter, decrease the cost of your energy bills, and increase the value of your home.
How much blown-in insulation do I need for 1000 sq ft?
If you’re aiming for R-30 (a common recommended value for attics per the Home Depot chart), the GreenFiber chart gives 40.8 bags per 1,000 square feet of gross coverage. Divide the measured square footage you obtained by 1,000 square feet to obtain the multiplication factor: 1,500 square feet/1,000 square feet = 1.5.
Can you put too much insulation in your attic?
It’s possible to over-insulate an attic as too much will cause moisture buildup and eventually result in mold. Eventually, adding more insulation leads to diminishing returns in trapping heat as well.
Which is better attic insulation blown or rolled?
Rolled fiberglass insulation scores an R-value of 3.7. So overall, rolled fiberglass insulation is slightly more effective at blocking in and out heat than its blown counterpart.
Can you put new insulation over old?
According to ENERGY STAR®, you can put new insulation over old insulation, “unless it is wet. The vapor retarder on top of or between layers of insulation can trap moisture. Any existing batt or roll insulation in the attic should have the facing against the attic drywall floor or no facing at all.
Can I insulate my attic myself?
For DIY attic insulation, you’ve got two choices: loose fill or batt (the common term for blanket insulation). Both can be added to uninsulated attics or layered over existing material. Once you’ve decided which type is best for you, examine the material options and prices to home in on the right product.
Which insulation is best for attic?
Many people consider fiberglass batt to be the best attic insulation. It consists of plastic reinforced by small glass fibers. The batt version comes in blanket form — i.e., small, pre-cut sections that you can lay down wherever you need to.
Should I remove old attic insulation before adding new?
Expert contractors that specialize in insulation advise that removing old fiberglass insulation is best before installing new cellulose insulation because of possible mildew, mold, or rodent excrement. So, by have attic insulation removal service, you are getting rid of those possible issues.
How much blown insulation do I need in my attic?
The higher the R-Value, the better the thermal performance of the insulation. The recommended level for most attics is to insulate to R-38 or about 10 to 14 inches, depending on insulation type.
Which is better foam or blown insulation?
Between spray foam and blown-in cellulose, which is better? Both spray foam and blown-in cellulose insulation have their advantages. Spray foam has a higher R-value, so it’s the more effective insulator. But cellulose is better at insulating street noise.
How many inches is R30 blown insulation?
Fiberglass Chart R-Value Thickness Bags / 1000 Sq Ft R49 16.25” 22.6 R44 14.75” 20.1 R38 12.75” 16.8 R30 10.25” 13.0.
How do I calculate how much insulation I need for my walls?
Measure the height and width of any windows or doors in the wall. Multiply the measurements to find the area of each window or door, and subtract them from the total square footage of the wall. This gives you the square footage of insulation you need for that wall.
What is the R-value of 14 inches of blown insulation?
Warm Climates (R-30 to R-49): Fiberglass (blown): 14” – 18” Fiberglass (batts): 11” – 14” Cellulose (blown): 11” – 13”.
Can you put batt insulation over blown in?
A: There’s no problem with installing fiberglass batts over your existing blown-in insulation. The reason for this precaution is that the facing on the insulation batts is a vapor barrier, which is intended to prevent moisture vapor from penetrating into the insulation.
How often should you insulate your attic?
How often should attic insulation be changed? Even though attic insulation is said to last anywhere from 80 years to 100 years, it does lose effectiveness as its ages. Insulation experts recommend replacing after 15 years to assure it is doing the job you need it to.
How much R-value do I need in attic?
For homes in California, the attic should achieve an R-value between R-30 and R-60. Most areas of the country have a higher minimum R-value recommendation, but just about everywhere recommends up to R-60.
Why are old houses not insulated?
Classic, older homes may radiate beauty and charm, but they are often uncomfortably drafty – especially during cold months. Unlike today’s airtight homes, many old houses have a natural ventilation system. They “breathe” through air leaks, and houses built before the 1960s were usually not well insulated.
